|
|
PDF MX121 Data sheet ( Hoja de datos )
| Número de pieza | MX121 | |
| Descripción | A/V Control Center Owner Manual | |
| Fabricantes | McIntosh | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MX121 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com
MX121
A/V Control Center
Owner’s Manual
1 page  
General Information
General Information
1. For additional connection information, refer to the
owner’s manual(s) for any component(s) connect-
ed to the MX121 A/V Control Center.
2. The Main AC Power going to the MX121 and
any other McIntosh Component(s) should not
be applied until all the system components are
connected together. Failure to do so could result
in malfunctioning of some or all of the system’s
normal operations. When the MX121 and other
McIntosh Components are in their Standby Power
Off Mode, the Microprocessor’s Circuitry inside
each component is active and communication is
occurring between them.
3. Sound Intensity is measured in units called Deci-
bels and “dB” is the abbreviation.
4. LFE (Low Frequency Effects) refers to the Dolby
Digital or DTS sound channel dedicated to sound
effects (such as explosions) and is usually repro-
duced by the Subwoofer.
5. When discarding the unit, comply with local rules
or regulations. Batteries should never be
thrown away or incinerated but disposed
of in accordance with the local regula-
tions concerning battery disposal.
6. For additional information on the
MX121 and other McIntosh Products
please visit the McIntosh Web Site at
www.mcintoshlabs.com.
7. The Main Zone accepts Audio Input Signals from
the HDMI, iPod/USB, Coaxial/Optical Digital
and unbalanced/balanced Analog Input Connec-
tions.
8. The Zones 2 and 3 accept Audio Input Signals
from the iPod/USB, Coaxial/Optical PCM Digital
Signals and unbalanced/balanced Analog Input
Connections.
Note: When connecting source devices with HDMI
Outputs to the MX121, make sure to also con-
nect the unbalanced/balanced Analog Output
or Coaxial/Optical Digital Audio Output for
each HDMI Source connected to MX121.
9. The Main Zone accepts Video Input Signals from
the HDMI, Component Video and Composite
Video Input Connections.
10. Zone 2 accepts Video Input Signals from the
Component Video and Composite Video Input
Connections.
11. Zone 3 is for Audio Signal Sources only.
12. MX121 is a three Zone Product (Main Zone, Zone
2 and Zone 3). This allows two different Audio/
Video Sources to be available simultaneously
for two separate rooms. Zone 2 may be used to
provide an Audio/Video Output Signal for record-
ing purposes, instead of an A/V signal to a second
room. The Zone 3 allows for listening to a differ-
ent Audio Source from either the Main Zone or
Zone 2. For more information contact your McIn-
tosh Dealer or McIntosh Technical Support.
13. The IR Input with 1/8 inch mini phone jack is
compatible IR sensors such as a Xantech Model
HL85BK Kit. Use a Connection Block such as a
Xantech Model ZC21 when two or more IR sen-
sors need to be connected to the MX121. To avoid
possible interaction, disable the MX121 Front
Panel Sensor. Refer to “IR Sensor" on page 27.
14. Setup Mode operations should be performed in
the order they appear in the first Setup Menu
presented, as they are interactive.
15. To hear bass frequencies below 80Hz, your system
must include either a Subwoofer or Large Front
Loudspeakers.
16. The MX121 has built-in HDMI Digital Video
Selection and Digital Video Processing Circuitry
with scaling capabilities to convert Composite or
Component Video Signals to Digital Video.
17. When there is a connection between the HDMI
Output and a TV/Monitor, the On-Screen Over-
lays including Menus, will only appear on the
HDMI Output.
18. HDMI Cable lengths between source components
and the MX121 also between the MX121 and the
TV/Monitor, should not exceed 25ft (8.3m). If
there is need to use HDMI Cables longer than 25ft
(8.3m) a high quality in line HDMI Buffer/Con-
verter would be required for reliable digital signal
transmission via the HDMI Connections.
19. The MX121 is designed to pass through a 3D
Digital Video Signal from a source component
to a 3D TV/Monitor via the HDMI Connections.
It is extremely important the HDMI cables used
for connections meet or exceed the HDMI High
Speed Cable Standards (1.4a) for proper 3D Video
Playback.
20. The Remote Control Supplied with the MX121
A/V Control Center is capable of operating other
components. For additional information go to
www.mcintoshlabs.com.
21. The MX121 is compatible with the following
Apple Mobile Devices with the latest version of
the Apple OS Software installed:
iPod touch (4th generation) iPhone 4S
iPod touch (3rd generation)
iPhone 4
iPod touch (2nd generation) iPhone 3GS
iPod touch (1st generation)
iPhone 3G
iPod classic
iPhone
iPod nano (6th generation)
iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
5
5 Page 
MX121 Main Zone Input Connections
MX121 Main Zone Input Connections
The MX121 has the ability to automatically switch
power On/Off to McIntosh Source Components via
the Power Control/Trigger connections. The Data Port
Connections allow for the remote operation of basic
functions using the MX121 Remote Control. With an
external sensor connected, remote control operation of
the system is possible when the MX121 is located in a
cabinet with the doors closed (Main Zone).
The Main Zone connection instructions below,
together with the MX121 Input Connection Diagram
located on the separate folded sheets “Mc2A”, is an
example of a typical Home Theater System. Your
system may vary from this, however the actual com-
ponents would be connected in a similar manner. For
additional information refer to “Connector and Cable
Information” on page 6.
Note: The following source component and sensor con-
nections made to the MX121 are using the default
settings. Refer to page 24.
Power Control Connections:
1. Connect a Control Cable from the MX121 PWR
CTRL TRIGGER 1 Jack to the Power Control
Remote In on the Turntable.
2. Connect a Control Cable from the Turntable
Power Control Remote Out jack to the AM/FM
Tuner Power Control In Jack.
3. Connect a Control Cable from the AM/FM Tuner
Power Control Out Jack to the Audio/Video Disc
Player Power Control In Jack.
4. Connect any additional McIntosh Components in
a similar manner, as outlined in steps 1 thru 3.
5. Connect a Control Cable from the Power Control
Output Jack (from the last component a Power
Control Input connection was made) onto the first
Power Amplifier with a Power Control Input jack.
Data Control Connections:
6. Connect a Control Cable from the MX121 DATA
OUT Jack to the AM/FM Tuner Data In Jack.
IR In Connections:
7. Optionally, connect the Control Cable from the
Main Zone External Sensor (or external IR Con-
nection Block) to the MX121 IR IN Jack.
Note: Refer to page 5 for information on compat-
ible Sensors and page 6 for Cable/Connection
information.
Analog Audio Connections:
8. Connect an Audio Cable from the MX121 ANA-
LOG AUDIO IN TUNER Jacks to the Tuner
unbalanced Analog Output Jacks.
9. Connect Balanced Cables from the MX121 AUX
1 BALANCED IN Jacks to the Audio/Video Disc
Player Audio Outputs Balanced 2 CHannel Jacks.
10. Connect an Audio Cable from the MX121 ANA-
LOG AUDIO IN VCR Jacks to the VCR Analog
Output Jacks.
11. Connect Audio Cables from the MX121 ANALOG
AUDIO IN PHONO Jacks to the Turntable Out
Jacks.
Digital Audio Connections:
12. Connect a Digital Coaxial Cable from the MX121
Digital COAX IN 2 Jack to the Satellite Reciever
Digital Coaxial Output Jack.
Analog Video Connections:
13. Connect a Video Cable from the MX121 COMPO-
NENT VIDEO IN 2 Jacks to the Satellite Reciever
Component Video Output Jacks, making sure to
match the “Y”, “PB” and “PR” connections at both
ends of the cable.
HDMI Connections:
14. Connect a HDMI Cable from the MX121 HDMI
IN 1 Connector to the Audio/Video Disc Player
HDMI Out Connector.
Ground Connections:
15. Connect a Ground Cable from the MX121 GND
Binding Post to the Turntable GND Binding Post.
Proceed to Main Zone Output Connections on the
next page.
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet MX121.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MX120 | Diode ( Rectifier ) |  American Microsemiconductor |
| MX121 | A/V Control Center Owner Manual | McIntosh |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |