|
International Rectifier |
Data sheet No. PD60282
IPS6041(G)(R)(S)PbF
INTELLIGENT POWER HIGH SIDE SWITCH
Features
• Over temperature shutdown (with auto-restart)
• Short circuit protection (current limit)
• Reverse battery protection (turns On the MOSFET)
• Full diagnostic capability (short circuit to battery)
• Active clamp
• Open load detection in On and Off state
• Ground loss protection
• Logic ground isolated from power ground
• ESD protection
Description
The IPS6041(G)(R)(S)PbF is a five terminal Intelligent
Power Switch (IPS) for use in a high side configuration. It
features short circuit, over-temperature, ESD protection,
inductive load capability and diagnostic feedback. The
output current is limited to the Ilim value. The current
limitation is activated until the thermal protection acts. The
over-temperature protection turns off the device if the
junction temperature exceeds the Tshutdown value. It will
automatically restart after the junction has cooled 7°C
below the Tshutdown value. The reverse battery
protection turns On the MOSFET. A diagnostic pin
provides different voltage levels for each fault condition.
The double level shifter circuitry will allow large offsets
between the logic and load ground.
Typical Connection
Product Summary
Rds(on)
Vclamp
I Limit
Open load
130mΩ max.
39V
7A
3V / 0.22A
Packages
SO8
IPS6041GPbF
D-Pak
IPS6041RPbF
TO220
IPS6041PbF
D2Pak
IPS6041SPbF
+5V +Bat
Rdgp
Dg(3)
Rdgs
Vcc(5-6-7-8)
Control
V Diag
Input Signal
In(2) Gnd(1)
Rin
Out(4)
Load
Pull-up resistors required for
open load off and short
circuit to Vbat detection
www.irf.com
1
Free Datasheet http://www.Datasheet4U.com
IPS6041(G)(R)(S)PbF
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters
are referenced to Ground lead. (Tambient=25°C unless otherwise specified).
Symbol Parameter
Min. Max. Units
Vout
Maximum output voltage
Vcc-35 Vcc+0.3
Voffset
Maximum logic ground to load ground offset
Vcc-35 Vcc+0.3
Vin Maximum input voltage
-0.3 5.5
V
Vcc max. Maximum Vcc voltage
⎯ 36
Vcc cont. Maximum continuous Vcc voltage
⎯ 28
Iin max.
Idg max.
Maximum IN current
Maximum diagnostic output current
-3
-3
10
10
mA
Vdg Maximum diagnostic output voltage
-0.3 5.5
V
Maximum power dissipation (internally limited by thermal protection)
Pd
Rth=100°C/W IPS6041G
⎯ 1.25 W
Rth=50°C/W IPS6041R 1”sqrt. footprint ⎯
2.5
Electrostatic discharge voltage (Human body) C=100pF, R=1500Ω
Between In and Vcc
⎯ 1500
ESD
Other combinations
Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω,L=10µH
⎯ 4000
V
Between In and Vcc
⎯ 100
Other combinations
⎯ 500
Tj max.
Max. storage & operating temperature junction temperature
-40 150
°C
Tsoldering Soldering temperature (10 seconds)
⎯ 300 °C
Thermal Characteristics
Symbol
Parameter
Rth1
Thermal resistance junction to ambient IPS6041G
Rth1
Thermal resistance junction to ambient IPS6041R D-Pak std. footprint
Rth2
Thermal resistance junction to ambient IPS6041R D-Pak 1” sqrt. footprint
Rth3
Thermal resistance junction to case IPS6041(R)(S) D-Pak/D2pak/TO220
Rth1
Thermal resistance junction to ambient IPS6041(S) D2Pak/TO220 std.
footprint
Rth2
Thermal resistance junction to ambient IPS6041S D2Pak 1” sqrt. footprint
Typ.
100
70
50
6
60
40
Max.
⎯
⎯
⎯
⎯
⎯
⎯
Units
°C/W
Recommended Operating Conditions
These values are given for a quick design. For operation outside these conditions, please consult the application notes.
Symbol
Parameter
Min. Max. Units
VIH High level input voltage
4 5.5
VIL Low level input voltage
0 0.9
Iout Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V
Rth=100°C/W IPS6041G
⎯ 1.6
A
Rth=50°C/W IPS6041R 1” sqrt. footprint
⎯ 2.3
Rin Recommended resistor in series with IN pin
4 10
Rdgs
Rdgp
Recommended resistor in series with DG pin for reverse battery protection
Recommended pull-up resistor for DG
4
4
20
20
kΩ
Rol Recommended pull-up resistor for open load detection
5 100
F max.
Max. switching frequency
⎯ 3.5 kHz
www.irf.com
2
Free Datasheet http://www.Datasheet4U.com
|