|
|
PDF CS-800 Data sheet ( Hoja de datos )
| Número de pieza | CS-800 | |
| Descripción | Full Duplex Interconnect | |
| Fabricantes | CONNECT SYSTEMS | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CS-800 (archivo pdf) en la parte inferior de esta página. Total 32 Páginas | ||
|
No Preview Available !
CONNECT SYSTEMS INC.
1802 Eastman Ave. Suite 116
Ventura, Ca. 93003
Phone (805) 642-7184
Fax (805) 642-7271
Model CS-800
Full Duplex Interconnect
USER'S INSTRUCTION MANUAL
Revised 10/94
Made in U.S.A.
Copyright (C) 1991 By Connect Systems Inc.
Connect Systems Inc. - Model CS-800
Page 1
Free Datasheet http://www.datasheet4u.com/
1 page  
P4 STATUS TONES
P5 COS
P6 RPT AUDIO
P7 HYBRID BALANCE
Status beeps & CW ID level: Adjust for
desired modulation level of status beeps or
CW ID.
COS Threshold level: Measure the voltage at
TP-1 with no signal. Then measure the voltage
again with a signal applied. Adjust P-5 until
the voltage reading at TP-2 is approximately
midway between the two readings previously
obtained at TP-1.
For example: If TP-1 read 2 volts with no
signal, and 4 volts with a signal applied to
the receiver, TP-2 would be set to read
3 volts.
When JP-2 is correctly strapped and P5 is
properly adjusted, the RX LED will be
illuminated when there's a signal and go out
when the signal is removed.
Repeat Audio: Sets the modulation level of
repeat audio in repeater mode. Adjust only
after adjustment of P1 has been completed.
See discussion next page.
JUMPER STRAP OPTIONS
JP-1
De-emphasis strap. De-emphasizes the incoming audio (use when
taking audio directly from the FM detector). Cut JP-1 when
connecting to a source of flat audio such as the high side of
the volume control.
JP-2 COS polarity select strap. Strap in = non inverted. Remove
plastic clip for polarity inversion.
JP-3 Audio output range strap. Strap in = low level (0-1 V). Strap
cut = high level (0-5 V). Strap factory installed.
JP-4
Selects whether the Aux. Relay output is normally open (NO) or,
normally closed (NC). JP-5 is factory strapped for NO. For NC
operation, connect the center pad to the NC pad.
JP-5
Line in use detect strap. Must be installed if the 'line in
use' feature is to be used (See programming line 1.2.). Be sure
to program line 1.2. with a 0 (to disable) if JP-5 is not
strapped.
To enable line in use detect, simply slide the plastic clip off
one of the posts, and re-install over both posts. Be sure to
program line 1.2. with a '1'.
Connect Systems Inc. - Model CS-800
Page 5
Free Datasheet http://www.datasheet4u.com/
5 Page 
This choice allows selecting any morse code character from Table
1 (page 17) as the courtesy beep. The default is 17 which sends
"R" for roger. If a short beep is desired enter a 4. For a long
beep enter 19.
INTERCONNECT OPERATING PARAMETERS
[Branch to]
0.8. Interconnect Operating Mode
1 = Semi-Duplex
2 = Full Duplex
0 = Disable
DEFAULT: 2 = Full Duplex
[0.9.]
[1.0.]
[A.A.]
0.9. Semi-Duplex Privacy Mode
1 = Enable
0 = Disable
DEFAULT: 0 = Disable
In privacy mode, the mobile side of the conversation is not re-
transmitted. Thus eavesdroppers only hear one half of the
conversation. Thus providing some conversation privacy.
1.0. Access Code Remote Programming Code
xxxx = User selectable remote programming code
Protocol: ###xxxx (Enters Remote Programming Mode)
DEFAULT: 9876
Selects the code which is used to enter the remote programming
mode. The remote programming mode permits the remote selection or
changing of the interconnect access code(s). See Remote Access
Code Programming page 18 for more detail.
1.1. Disconnect Code
0 = # Down
1 = # Plus Connect Code
DEFAULT: 0 = # Down
Choose the patch disconnect code. Enter 0 to select # down in
most applications. Or enter 1 to select # plus the connect code
digits.
1.2. Line in Use Detect
1 = Enable
0 = Disable
DEFAULT: 1 = Enable
When enabled, mobiles are prevented from cutting in on calls that
are already in progress on the same line.
NOTE: JP-5 must be strapped for line in use detection to operate.
Please refer to page 5 for additional details on Jumper Strap
options.
Connect Systems Inc. - Model CS-800
Page 11
Free Datasheet http://www.datasheet4u.com/
11 Page | ||
| Páginas | Total 32 Páginas | |
| PDF Descargar | [ Datasheet CS-800.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CS-800 | Full Duplex Interconnect | CONNECT SYSTEMS |
| CS-800 | OPERATION MANUAL |  ELTRA |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |