|
|
PDF VRCD400-SDU Data sheet ( Hoja de datos )
| Número de pieza | VRCD400-SDU | |
| Descripción | Owner Manual | |
| Fabricantes | Virtual Reality Sound Labs | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de VRCD400-SDU (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
|
No Preview Available !
www.DataSheet4U.net
VRCD400-SDU
OWNER’S MANUAL
AM/FM Receiver, CD/MP3/WMA Player with
USB Port, Aux In, & Detachable Face
• AM/FM MPX STEREO
• MP3 / WMA WITH ID3 DISPLAY
• ASPS MEMORY CONTROL
• AUTO SEEK UP / DOWN
• FM STEREO / MONO
• 30 PRESET MEMORY
• MIX BAS / TRE / BAL / FAD SWITCH
• AUTO CD PLAY / RADIO
• AUTO POWER LOADING
• LOUDNESS CONTROL
• MUTE SOUND CONTROL
• USB CONTROL FOR MP3 / WMA
• WIRE HARNESS ON PLUG
• DIGITAL LCD DISPLAY
• DUAL CHANNEL LEVEL METER
• TIME CLOCK DISPLAY
• PRESET EQ (POP, ROCK,
FLAT, CLASSIC)
• BUILT IN NOISE FILTER
• BUILT IN RCA OUTPUT
• SUBWOOFER OUTPUT
• AUXILIARY INPUT
• AUTO ANTENNA ACTIVATOR
• INFRA RED REMOTE CONTROL
www.DataSheet4U.net
1 page  
www.DataSheet4U.net
Before You Install
Automotive audio equipment installations can be troublesome at times, even to the most
experienced of installation technicians. If you are not confident working with electrical
wiring, removing and reinstalling interior panels, carpeting, dashboards or other compo-
nents of your vehicle, please call our toll-free help line 1-800-445-1797 and our in-house
technical service team will answer your installation questions. Contact the vehicle's
manufacturer for vehicle specific instructions, or consider having the VRCD400-SDU
professionally installed.
IMPORTANT: Remove the two transport screws from the top of the unit before installing.
1. Remove the Old Unit from the Dashboard
A. Remove the outer trim frame.
B. Insert the keys supplied with the old unit
into both sides of the unit as shown in fig-
ure below until they click. Pull to remove
the old unit from the dashboard.
DIN Front Mount
DO NOT DISCONNECT WIRES AT THIS TIME!
2. Mark Polarity of the Speaker Wires
Marking the polarity of the speaker
wires will make it easier to connect the
existing speakers to the VRCD400-SDU.
Consult wiring diagram of existing head
unit before disconnecting any wires. If a
wiring diagram is not available contact
the manufacturer.
1. While the old unit is playing, discon-
nect the wires from one speaker.
2. Take a length of masking tape and
fold it around the wire so it forms a
flag.
3. On the masking tape mark the polar-
ity of the speaker wires (+ & - ), as
well as left or right, and front or rear.
4. Double check that you marked the
first speaker correctly by checking
that the speaker wires are the same at
the head unit.
5. Repeat this procedure for all of the
speakers.
6. Mark the power, ground, and any
other wires also.
4 www.DataSheet4U.net
5 Page 
www.DataSheet4U.net
Basic Operation
1. Tuning the Unit On / Off
Press the any button to turn the unit on, the
display will show a message WELCOME
to indicate it is ready for use. Press and hold
the POWER button again to turn the unit
off.
2. Mode Selection
Press the BD/ID3 for the Radio mode, Press
the “MOD” Button to select the play mode
between AUX, RADIO and CD PLAY.
speakers.
10. Subwoofer Control
Press and hold the SEL button until LCD
display “DSP OFF”. Press SEL button
again and LCD display “WOOFER OFF’.
Rotate volume to activate the subwoofer
control function, then leave the unit idle for
your desired setting to take effect. Make
sure the unit is connected to an external
amplifier.
3. Loudness Control
11. Time Clock Setting
Press the LUD Button to emphasize the The time clock can be set anytime when
Bass output, the word “LOUD ON” shown the power is on. Press the CLK Button and
on the display indicates that the loudness then press and hold “CLK” Button for 3
function is on. Press again to cancel.
seconds, the time will blink on the display.
4. Mute Control
Press the MUT Button to activate the Mute
function. Press again or rotate the volume
knob to cancel.
1. Rotate the volume up button to adjust the
hour.
2. Rotate the volume down button to adjust
the minute.
3. Press the CLK Button again or leave the
5. Volume
unit idle for new setting to effect.
Adjust Volume by simply rotating the vol- Press the CLK Button anytime to view the
ume knob, the display shows VOL then 0 time clock display.
(indicate the volume level).
12. Preset Beep Sound Off
6. Bass
1. Press the Sound Select button for 2
Press SEL button until the display shows Seconds, the Display will show “DSP OFF”.
BAS 0. Rotate the knob to adjust the bass 2. Press the Sound Select button continu-
of high/low sound level.
ously until the display show “BEEP ON”,
7. Treble
Press SEL button until the display shows
TRE 0. Rotate the knob to adjust the bass
of high/low sound level.
press the volume up/down button to toggle
between it and “BEEP OFF”, then leave
the unit idle for your desired setting to take
effect.
8. Balance
Press SEL button until the display shows
BAL R-L. Rotate the knob to adjust the bal-
ance of left/right speakers.
13. Preset Equalizer Function
Press and hold the SEL Button for 2 sec-
onds, the display will show “DSP OFF”.
Rotate the Volume up/down button to choose
set the EQ sound effects. The choices are
9. Fader
POP, ROCK, CLASS, and FLAT.
Press SEL button until the display shows
FAD F-R. Rotate the knob to adjust the
volume balance between the front & rear
10
www.DataSheet4U.net
11 Page | ||
| Páginas | Total 22 Páginas | |
| PDF Descargar | [ Datasheet VRCD400-SDU.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| VRCD400-SDU | Owner Manual | Virtual Reality Sound Labs |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |