파트넘버.co.kr DS1023 데이터시트 PDF


DS1023 반도체 회로 부품 판매점

8-Bit Programmable Timing Element



Dallas Semiconducotr 로고
Dallas Semiconducotr
DS1023 데이터시트, 핀배열, 회로
DS1023
8-Bit Programmable Timing Element
www.dalsemi.com
FEATURES
Step sizes of 0.25 ns, 0.5 ns, 1 ns, 2 ns, 5 ns
On-chip reference delay
Configurable as delay line, pulse width
modulator, or free-running oscillator
Can delay clocks by a full period or more
Guaranteed monotonicity
Parallel or serial programming
Single 5V supply
16-pin DIP or SOIC package
PIN ASSIGNMENT
IN
LE
Q/P0
CLK/P1
D/P2
P3
P4
GND
1
2
3
4
5
6
7
8
16 VCC
15 OUT/OUT
14 P/S
13 P7
12 P6
11 MS
10 P5
9 REF/PWM
DS1023 300-mil DIP
DS1023S 300-mil SOIC
PIN DESCRIPTION
IN - Input
P0/Q
- Parallel Input P0 (parallel mode)
- Serial Data Output (serial mode)
P1/CLK
- Parallel Input P1 (parallel mode)
- Serial Input Clock (serial mode)
P2/D
- Parallel Input P2 (parallel mode)
- Serial Data Input (serial mode)
P3 - P7
- Remaining Parallel Inputs
GND
- Ground
OUT/ OUT - Output
REF/PWM - Reference or PWM Output
P /S - Parallel / Serial Programming
Select
MS - Output Mode Select
LE - Input Latch Enable
VCC - Supply Voltage
DESCRIPTION
The DS1023 is an 8-bit programmable delay line similar in function to the DS1020/DS1021.
Additional features have been added to extend the range of applications:
The internal delay line architecture has been revised to allow clock signals to be delayed by up to a full
period or more. Combined with an on-chip reference delay (to offset the inherent or “step zero” delay of
the device) clock phase can now be varied over the full 0-360 degree range.
1 of 16
022300


DS1023 데이터시트, 핀배열, 회로
DS1023
On-chip gating is provided to allow the device to provide a pulse width modulated output, triggered by
the input with duration set by the programmed value.
Alternatively the output signal may be inverted on chip, allowing the device to perform as a free-running
oscillator if the output is (externally) connected to the input.
PROGRAMMING
The device programming is identical to the DS1020/DS1021. Note, however, that the serial clock and
data pins are shared with three of the parallel input pins.
The P /S pin controls the same function as “Mode Select” on the DS1020/DS1021 (but with reversed
polarity). A low logic level on this pin enables the parallel programming mode. LE must be at a high
logic level to alter the programmed value; when LE is taken low the data is latched internally and the
parallel data inputs may be altered without affecting the programmed value. This is useful for
multiplexed bus applications. For hard-wired applications LE should be tied to a high logic level.
When P /S is high serial programming is enabled. LE must be held high to enable loading or reading of
the internal register, during which time the delay is determined by the previously programmed value.
Data is clocked in MSB to LSB order on the rising edge of the CLK input. Data transfer ends and the
new value is activated when LE is taken low.
PARALLEL MODE ( P /S = 0)
In the PARALLEL programming mode, the output of the DS1023 will reproduce the logic state of the
input after a delay determined by the state of the eight program input pins P0 - P7. The parallel inputs
can be programmed using DC levels or computer-generated data. For infrequent modification of the
delay value, jumpers may be used to connect the input pins to VCC or ground. For applications requiring
frequent timing adjustment, DIP switches may be used. The latch enable pin (LE) must be at a logic 1 in
hardwired implementations.
Maximum flexibility is obtained when the eight parallel programming bits are set using computer-
generated data. When the data setup (tDSE) and data hold (tDHE) requirements are observed, the enable pin
can be used to latch data supplied on an 8-bit bus. Latch enable must be held at a logic 1 if it is not used
to latch the data. After each change in delay value, a settling time (tEDV or tPDV) is required before input
logic levels are accurately delayed.
SERIAL MODE ( P /S = 1)
In the SERIAL programming mode, the output of the DS1023 will reproduce the logic state of the input
after a delay time determined by an 8-bit value clocked into serial port D. While observing data setup
(tDSC) and data hold (tDHC) requirements, timing data is loaded in MSB-to-LSB order by the rising edge of
the serial clock (CLK). The latch enable pin (LE) must be at a logic 1 to load or read the internal 8-bit
input register, during which time the delay is determined by the last value activated. Data transfer ends
and the new delay value is activated when latch enable (LE) returns to a logic 0. After each change, a
settling time (tEDV) is required before the delay is accurate.
As timing values are shifted into the serial data input (D), the previous contents of the 8-bit input register
are shifted out of the serial output pin (Q) in MSB-to-LSB order. By connecting the serial output of one
DS1023 to the serial input of a second DS1023, multiple devices can be daisy-chained (cascaded) for
programming purposes (Figure 1). The total number of serial bits must be eight times the number of units
daisy-chained and each group of 8 bits must be sent in MSB-to-LSB order.
2 of 16




PDF 파일 내의 페이지 : 총 16 페이지

제조업체: Dallas Semiconducotr

( dallas )

DS1023 data

데이터시트 다운로드
:

[ DS1023.PDF ]

[ DS1023 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


DS1020

Programmable 8-Bit Silicon Delay Line - Dallas Semiconducotr



DS1021

Programmable 8-Bit Silicon Delay Line - Dallas Semiconducotr



DS1023

8-Bit Programmable Timing Element - Dallas Semiconducotr