파트넘버.co.kr S9318 데이터시트 PDF


S9318 반도체 회로 부품 판매점

Nonvolatile DACPOT Electronic Potentiometer With Up/Down Counter Interface



ETC 로고
ETC
S9318 데이터시트, 핀배열, 회로
SUMMIT
MICROELECTRONICS, Inc.
Nonvolatile DACPOT™ Electronic Potentiometer
With Up/Down Counter Interface
S9318
FEATURES
• Digitally Controlled Electronic Potentiometer
• 8-Bit Digital-to-Analog Converter (DAC)
– Independent Reference Inputs
– Differential Non-Linearity - ±0.5LSB max
– Integral Non-Linearity - ±1LSB max
• VOUT Value in E2PROM for Power-On Recall
– Equivalent to 256-Step Potentiometer
• Unity Gain Op Amp Drives up to 1mA
• Simple Trimming Adjustment
– Up/Down Counter Style Operation
• Low Noise Operation
• “Clickless” Transitions between DAC Steps
• No Mechanical Wearout Problem
– 1,000,000 Stores (typical)
– 100 Year Data Retention
• Operation from +2.7V to +5.5V Supply
• Low Power, 1mW max at +5V
OVERVIEW
The S9318 DACPOT™ trimmer is an 8-bit nonvolatile
DAC designed to replace mechanical potentiometers.
The S9318 includes a unity-gain amplifier to buffer the
DAC output and enables VOUT to swing from rail to rail.
The DACPOT trimmer operates over a supply voltage
range of 2.7V to 5.5V.
The S9318’s simple up/down counter input provides an
ideal interface for automatic test equipment to dither and
monitor the VOUT voltage. This interface allows for quick
and consistent calibration of even the most sophisticated
systems.
The S9318 is a pin-compatible performance upgrade for
other industry nonvolatile potentiometers. The S9318
offers double the resolution of these devices and provides
‘clickless’ transitions of VOUT.
FUNCTIONAL BLOCK DIAGRAM
8-bit E2 PROM
VDD
UP/DN
INC
CS
Counter
&
Write
Control
8-bit
Data
Register
8-bit DAC
GND
-
AMP
+
VH
VOUT
VL
2016 ILL2.1
SUMMIT MICROELECTRONICS, Inc. • 300 Orchard City Drive, Suite 131 • Campbell, CA 95008 • Telephone 408-378-6461 • Fax 408-378-6586 • www.summitmicro.com
© SUMMIT MICROELECTRONICS, Inc. 1999
2016-04 4/24/99
Characteristics subject to change without notice
1


S9318 데이터시트, 핀배열, 회로
PIN NAMES
Symbol
INC
UP/DN
VH
GND
VOUT
VL
CS
VDD
Description
Increment Input, High to Low
Edge Trigger
Up/Down Input controlling relative
VOUT movement
V+ reference input
Analog and Digital Ground
Trimmed Voltage Output
V- reference input
Active low chip select input
Supply Voltage (2.7V to 5.5V)
PINOUT
INC
UP/DN
VH
GND
1
2
3
4
S9318
8 VDD
7 CS
6 VL
5 VOUT
2016 ILL1.1
Analog Section
The S9318 is an 8-bit, voltage output digital-to-analog
converter (DAC). The DAC consists of a resistor network
that converts an 8-bit value into equivalent analog output
voltages in proportion to the applied reference voltage.
Reference Inputs
The voltage differential between the VL and VH inputs
sets the full-scale output voltage range. VL must be equal
to or greater than ground (i.e. a positive voltage). VH must
be greater than VL and less than or equal to VDD. See
table on page 3 for guaranteed operating limits.
Output Buffer Amplifier
The voltage output is a precision unity-gain follower that
can slew up to 1V/µs.
Digital Interface
The interface is designed to emulate a simple up/down
counter, but instead of a parallel count output, a
ratiometric voltage output is provided.
Chip Select (CS) is an active low input. Whenever CS is
high the S9318 is in standby mode and consumes the
least power. This mode is equivalent to a potentiometer
that is adjusted to the required setting. When CS is low the
S9318 will recognize transitions on the INC input and will
move the VOUT either toward the VH reference or toward
the VL reference depending upon the state of the UP/DN
input.
The host may exit an adjustment routine in two ways:
deselecting the S9318 while INC is low will not perform a
store operation (a subsequent power cycle will recall the
original data); deselecting the S9318 while INC is high will
store the current VOUT setting into nonvolatile memory.
Increment (INC) is an edge triggered input. Whenever
CS is low and a high to low transition occurs on the INC
input, the VOUT voltage will either move toward VH or VL
depending upon the state of the UP/DN input.
UP/Down (UP/DN) is an input that will determine the VOUT
movement relative to VH and VL. When CS is low, UP/DN
is high and there is a high to low transition on INC, the
VOUT voltage will move (1/256th x VH-VL) toward VH.
When CS and UP/DN are low, and there is a high to low
transition on INC, the VOUT will move (1/256th x VH-VL)
toward VL.
2016-04 4/24/99
2




PDF 파일 내의 페이지 : 총 6 페이지

제조업체: ETC

( etc )

S9318 data

데이터시트 다운로드
:

[ S9318.PDF ]

[ S9318 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


S9318

Nonvolatile DACPOT Electronic Potentiometer With Up/Down Counter Interface - ETC



S9318S

Nonvolatile DACPOT Electronic Potentiometer With Up/Down Counter Interface - ETC