파트넘버.co.kr 74LS161 데이터시트 PDF


74LS161 반도체 회로 부품 판매점

BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS



Motorola Semiconductors 로고
Motorola Semiconductors
74LS161 데이터시트, 핀배열, 회로
BCD DECADE COUNTERS/
4-BIT BINARY COUNTERS
The LS160A / 161A / 162A / 163A are high-speed 4-bit synchronous count-
ers. They are edge-triggered, synchronously presettable, and cascadable
MSI building blocks for counting, memory addressing, frequency division and
other applications. The LS160A and LS162A count modulo 10 (BCD). The
LS161A and LS163A count modulo 16 (binary.)
The LS160A and LS161A have an asynchronous Master Reset (Clear)
input that overrides, and is independent of, the clock and all other control
inputs. The LS162A and LS163A have a Synchronous Reset (Clear) input that
overrides all other control inputs, but is active only during the rising clock
edge.
BCD (Modulo 10)
Binary (Modulo 16)
Asynchronous Reset
LS160A
LS161A
Synchronous Reset
LS162A
LS163A
Synchronous Counting and Loading
Two Count Enable Inputs for High Speed Synchronous Expansion
Terminal Count Fully Decoded
Edge-Triggered Operation
Typical Count Rate of 35 MHz
ESD > 3500 Volts
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC TC Q0 Q1 Q2 Q3 CET PE
16 15 14 13 12 11 10 9
1234
*R CP P0 P1
56
78
P2 P3 CEP GND
NOTE:
The Flatpak version
has the same pinouts
(Connection Diagram) as
the Dual In-Line Package.
*MR for LS160A and LS161A
*SR for LS162A and LS163A
PIN NAMES
PE
P0 – P3
CEP
CET
CP
MR
SR
Q0 – Q3
TC
Parallel Enable (Active LOW) Input
Parallel Inputs
Count Enable Parallel Input
Count Enable Trickle Input
Clock (Active HIGH Going Edge) Input
Master Reset (Active LOW) Input
Synchronous Reset (Active LOW) Input
Parallel Outputs (Note b)
Terminal Count Output (Note b)
LOADING (Note a)
HIGH
LOW
1.0 U.L.
0.5 U.L.
0.5 U.L.
1.0 U.L.
0.5 U.L.
0.5 U.L.
1.0 U.L.
10 U.L.
10 U.L.
0.5 U.L.
0.25 U.L.
0.25 U.L.
0.5 U.L.
0.25 U.L.
0.25 U.L.
0.5 U.L.
5 (2.5) U.L.
5 (2.5) U.L.
NOTES:
a) 1 TTL Unit Load (U.L.) = 40 µA HIGH/1.6 mA LOW.
b) The Output LOW drive factor is 2.5 U.L. for Military (54) and 5 U.L. for Commercial (74)
Temperature Ranges.
SN54/74LS160A
SN54/74LS161A
SN54/74LS162A
SN54/74LS163A
BCD DECADE COUNTERS/
4-BIT BINARY COUNTERS
LOW POWER SCHOTTKY
16
1
J SUFFIX
CERAMIC
CASE 620-09
16
1
N SUFFIX
PLASTIC
CASE 648-08
16
1
D SUFFIX
SOIC
CASE 751B-03
ORDERING INFORMATION
SN54LSXXXJ Ceramic
SN74LSXXXN Plastic
SN74LSXXXD SOIC
LOGIC SYMBOL
934 56
PE P0 P1 P2 P3
7 CEP
10 CET
TC 15
2 CP
*R Q0 Q1 Q2 Q3
1 14 13 12 11
VCC = PIN 16
GND = PIN 8
*MR for LS160A and LS161A
*SR for LS162A and LS163A
FAST AND LS TTL DATA
5-278


74LS161 데이터시트, 핀배열, 회로
SN54/74LS160A SN54/74LS161A
SN54/74LS162A SN54/74LS163A
STATE DIAGRAM
LS160A LS162A
0123
15
14
13
12 11 10
9
4
5
6
7
8
LS161A LS163A
01234
15 5
14 6
13 7
12 11 10 9
8
LOGIC EQUATIONS
Count Enable = CEP CET PE
TC for LS160A & LS162A = CET Q0 Q1 Q2 Q3
TC for LS161A & LS163A = CET Q0 Q1 Q2 Q3
Preset = PE CP + (rising clock edge)
Reset = MR (LS160A & LS161A)
Reset = SR CP + (rising clock edge)
Reset = (LS162A & LS163A)
NOTE:
The LS160A and LS162A can be preset to any state,
but will not count beyond 9. If preset to state 10, 11,
12, 13, 14, or 15, it will return to its normal sequence
within two clock pulses.
FUNCTIONAL DESCRIPTION
The LS160A / 161A / 162A / 163A are 4-bit synchronous
counters with a synchronous Parallel Enable (Load) feature.
The counters consist of four edge-triggered D flip-flops with
the appropriate data routing networks feeding the D inputs. All
changes of the Q outputs (except due to the asynchronous
Master Reset in the LS160A and LS161A) occur as a result of,
and synchronous with, the LOW to HIGH transition of the
Clock input (CP). As long as the set-up time requirements are
met, there are no special timing or activity constraints on any
of the mode control or data inputs.
Three control inputs — Parallel Enable (PE), Count Enable
Parallel (CEP) and Count Enable Trickle (CET) — select the
mode of operation as shown in the tables below. The Count
Mode is enabled when the CEP, CET, and PE inputs are HIGH.
When the PE is LOW, the counters will synchronously load the
data from the parallel inputs into the flip-flops on the LOW to
HIGH transition of the clock. Either the CEP or CET can be
used to inhibit the count sequence. With the PE held HIGH, a
LOW on either the CEP or CET inputs at least one set-up time
prior to the LOW to HIGH clock transition will cause the
existing output states to be retained. The AND feature of the
two Count Enable inputs (CET CEP) allows synchronous
cascading without external gating and without delay accu-
mulation over any practical number of bits or digits.
The Terminal Count (TC) output is HIGH when the Count
Enable Trickle (CET) input is HIGH while the counter is in its
maximum count state (HLLH for the BCD counters, HHHH for
the Binary counters). Note that TC is fully decoded and will,
therefore, be HIGH only for one count state.
The LS160A and LS162A count modulo 10 following a
binary coded decimal (BCD) sequence. They generate a TC
output when the CET input is HIGH while the counter is in state
9 (HLLH). From this state they increment to state 0 (LLLL). If
loaded with a code in excess of 9 they return to their legitimate
sequence within two counts, as explained in the state
diagram. States 10 through 15 do not generate a TC output.
The LS161A and LS163A count modulo 16 following a
binary sequence. They generate a TC when the CET input is
HIGH while the counter is in state 15 (HHHH). From this state
they increment to state 0 (LLLL).
The Master Reset (MR) of the LS160A and LS161A is
asynchronous. When the MR is LOW, it overrides all other
input conditions and sets the outputs LOW. The MR pin should
never be left open. If not used, the MR pin should be tied
through a resistor to VCC, or to a gate output which is
permanently set to a HIGH logic level.
The active LOW Synchronous Reset (SR) input of the
LS162A and LS163A acts as an edge-triggered control input,
overriding CET, CEP and PE, and resetting the four counter
flip-flops on the LOW to HIGH transition of the clock. This
simplifies the design from race-free logic controlled reset
circuits, e.g., to reset the counter synchronously after
reaching a predetermined value.
MODE SELECT TABLE
*SR PE CET CEP Action on the Rising Clock Edge ( )
LX X
HL X
HH H
HH
L
HH X
X
X
H
X
L
RESET (Clear)
LOAD (Pn Qn)
COUNT (Increment)
NO CHANGE (Hold)
NO CHANGE (Hold)
FAST AND LS TTL DATA
5-279
*For the LS162A and
*LS163A only.
H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care




PDF 파일 내의 페이지 : 총 6 페이지

제조업체: Motorola Semiconductors

( motorola )

74LS161 data

데이터시트 다운로드
:

[ 74LS161.PDF ]

[ 74LS161 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


74LS16

HEX INVERTER BUFFERS/DRIVERS - Texas Instruments



74LS160

BCD DECADE COUNTERS / 4-BIT BINARY COUNTERS - SYC



74LS160

BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS - ON Semiconductor



74LS160

Synchronous Decade Counters(direct clear) - Hitachi Semiconductor



74LS160

BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS - Motorola Semiconductors



74LS160A

Synchronous Decade Counters(direct clear) - Hitachi Semiconductor



74LS160A

BCD DECADE COUNTERS/ 4-BIT BINARY COUNTERS - ON Semiconductor



74LS160A

BCD DECADE COUNTERS / 4-BIT BINARY COUNTERS - Motorola Semiconductors



74LS161

BCD DECADE COUNTERS / 4-BIT BINARY COUNTERS - SYC