|
Sharp Electrionic Components |
S101S05V/S101S06V/S201S05V/S201S06V
S101S05V/S101S06V
S201S05V/S201S06V
SIP Type SSR with
Mounting Capability for
External Heat Sink
s Features
1. High radiation resin mold package.
2. RMS ON-state current
IT : MAX. 3Arms at TC<= 100˚C
( With heat sink)
3. Isolation voltage between input and output
(Viso: 3 000 Vrms )
4. Built-in zero-cross circuit
(S101S06V/S201S06V)
5. Recognized by UL, file No. E94758
Approved by CSA, No. LR63705
s Applications
1. OA equipment such as copiers
2. FA equipment
s Outline Dimensions
(Unit : mm )
* The metal parts marked *
are common to terminal 1 .
g Do not allow external connection.
( ) : Typical dimensions
18.5 ± 0.2
16.4 ± 0.3
φ 3.2 ± 0.2
5.5 ± 0.2
A (Model No.)
B
S101S05V
3A125VAC
S101S06V
S201S05V
3A265VAC
S201S06V
*
A
4 - 1.1 ± 0.2
4 - 1.25 ± 0.3
4 - 0.8 ± 0.2
B
+-
1 23 4
s Model Line-ups
No built-in
zero-cross circuit
Built-in
zero-cross circuit
For 100V lines
S101S05V
S101S06V
For 200V lines
S201S05V
S201S06V
s Absolute Maximum Ratings
(5.08) (7.62)
Internal connection diagram
S101S05V /S201S05V
(2.54)
0.6 ± 0.1 (1.4)
S101S06V /S201S06V
Zero-cross
circuit
1 2 34
1 Output (Triac T2 )
2 Output (Triac T1 )
3 Input ( + )
4 Input ( - )
1 2 34
1 Output (Triac T2 )
2 Output (Triac T1 )
3 Input ( + )
4 Input ( - )
(Ta = 25˚C )
Parameter
Symbol
Rating
S101S05V / S101S06V S201S05V / S201S06V
Input
Output
Forward current
Reverse voltage
RMS ON-state current
*1Peak one cycle surge current
Repetitive peak OFF-state voltage
Non-repetitive peak OFF-state voltage
Critical rate of rise of ON-state current
Operating freguency
*2 Isolation voltage
Operating temperature
Storage temperature
*3Soldering temperature
IF
VR
IT
I surge
V DRM
V DSM
dIT /dt
f
V iso
T opr
T stg
T sol
50
6
*43
30
400 600
400 600
40
45 to 65
3 000
- 25 to + 100
- 30 to + 125
260
*1 60Hz sine wave, start at Tj= 25˚C
*2 60Hz AC for 1 minute, 40 to 60% RH. Apply voltages between input and output, by the dielectric withstand
voltage tester with zero-cross circuit.( Input and output shall be shorted respectively)
( Note) When the isolation voltage is necessary at using external heat sink, please use the insulation sheet.
*3 For 10 seconds
*4 Tc<=100˚C
Unit
mA
V
A rms
A
V
V
A/ µ s
Hz
V rms
˚C
˚C
˚C
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”
S101S05V/S101S06V/S201S05V/S201S06V
s Electrical Characteristics
Input
Parameter
Foward voltage
Reverse current
Repetitive peak OFF-state current
RMS ON-state current
Output Holding current
Critical rate of rise of OFF-state voltage
Critical rate of rise of com-
mutating OFF-state voltage
Minimum trigger S101S05V/ S201S05V
current
S101S06V/ S201S06V
Isolation resistance
Transfer
charac-
teristics
Zero-cross voltage
S101S06V
S201S06V
Turn-on time
S101S05V/ S201S05V
S101S06V/ S201S06V
S101S05V/ S201S05V
Turn-off time
S101S06V/ S201S06V
Thermal resistance
( Between junction and case )
Thermal resistance
( Between junction and ambience )
Symbol
VF
IR
I DRM
VT
IH
dV/dt
(dV/dt)C
I FT
R ISO
Conditions
IF = 20mA
VR = 3V
V D = V DRM
Resistance load, I F = 20mA
IT = 1.5A rms
-
V D = 2/3V DRM
Tj = 125˚C, VD = 400V
dI t/d t = -1.5A/ms
VD = 12V, R L = 30Ω
VD = 6V, R L = 30Ω
DC500V, 40 to 60 % RH
VOX IF = 15mA
t on AC50Hz
t off AC50Hz
R th(j-c)
R th (j-a)
-
-
MIN.
-
-
-
-
-
30
4
-
-
1010
-
-
-
-
-
-
-
TYP.
1.2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6
(Ta = 25˚C )
MAX.
1.4
10 - 4
10 - 4
Unit
V
A
A
1.5 V rms
50 mA
- V/µ s
- V/µ s
15
mA
15
-Ω
35
V
35
1
ms
10
10
ms
10
- ˚C/W
- 45 - ˚C/W
Fig. 1 RMS ON-state Current vs.
Ambient Temperature
(1 ) With heat sink ( Al 100 x 100 x t 2mm)
(2 ) With heat sink (Al 50 x 50 x t 2mm)
5 Note ) With the Al heat sink set up vertically,
install it as shown in the figure
Torque : 0.4N • m
4
Apply thermal conductive silicone grease
on the heat sink mounting plate. Forcible
cooling shall not be carried out.
Al plate
SSR
3
(2) (1)
2
Without
heat sink
1
0
- 25 0
25 45 50 75 100 125
Ambient temperature T a (˚C)
Fig. 2 RMS ON-state Current vs.
Case Temperature
5
4
3
2
1
0
- 25 60 70 80 90 100 110 120 125 130
Case temperature T c ( ˚C)
|