파트넘버.co.kr SL1062A 데이터시트 PDF


SL1062A 반도체 회로 부품 판매점

Low Voltage Transmission Circuit with Dialler Interface



System Logic Semiconductor 로고
System Logic Semiconductor
SL1062A 데이터시트, 핀배열, 회로
SL1062A
Low Voltage Transmission Circuit
with Dialler Interface
The SL1062A is an integrated circuit that perform all speech and line
interface functions required in fully electronic telephone sets. They
perform electronic switching between dialling and speech. The ICs
operate at line voltage down to 1.6 V DC (with reduced performance)
to facilitate the use of more telephone sets connected in parallel.
Low DC line voltage: operates down to 1.6 V (excluding polarity
guard)
Voltage regulator with adjustable static resistance
Provides a supply for external circuits
Symmertical high-impedance inputs (64 K) for dynamic,
magnetic or piezo-electric microphones
Asymmetrical high-impedance input (32 K) for electret
microphones
DTMF signal input with confidence tone
Mute input for pulse or DTMF dialing:
active LOW (MUTE)
Receiving amplifier for dynamic, magnetic or piezo-electric
earpieces
Large gain setting ranges on microphone and earpiece amplifiers
Line loss compensation (line current dependent) for microphone
and earpiece amplifiers
Gain control curve adaptable to exchange supply
DC line voltage adjustment facility
ORDERING INFORMATION
SL1062AN Plastic
TA = -25° to 75° C
for package
PIN ASSIGNMENT
BLOCK DIAGRAM
SLS
System Logic
Semiconductor


SL1062A 데이터시트, 핀배열, 회로
SL1062A
PIN DESCRIPTION
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Designation
LN
GAS1
GAS2
QR
GAR
MIC-
MIC+
STAB
VEE
IR
DTMF
MUTE
VCC
REG
AGC
SLPE
Description
positive line terminal
gain adjustment; transmitting amplifier
gain adjustment; transmitting amplifier
non-inverting output; receiving amplifier
gain adjustment; receiving amplifier
inverting microphone input
non-inverting microphone input
current stabilizer
negative line terminal
receiving amplifier input
dual-tone multi-frequency input
mute input
possitive supply decoupling
voltage regulator decoupling
automatic gain control input
slope (DC resistance) adjustment
FUNCTIONAL DESCRIPTION
Supplies VCC, LN, SLPE, REG and STAB
Power for the IC and its peripheral circuits is usually
obtained from the telephone line. The supply voltage
is derived from the line via a dropping resistor and
regulated by the IC. The supply voltage VCC may also
be used to supply external circuits e.g. dialling and
control circuits.
Decoupling of the supply voltage is performed by a
capacitor between VCC and VEE. The internal voltage
regulator is decoupled by a capacitor between REG
and VEE.
The DC current flowing into the set is determined by
the exchange supply voltage Vexch, the feeding bridge
resistance Rexch and the DC resistance of the
telephone line Rline.
The circuit has an internal current stabilizer operating
at a level determined by a 3.6 Kresistor connected
between STAB and VEE (see Fig.1).
Figure 1. Supply arrengement
When the line current (Iline) is more than 0.5 mA
greater than the sum of the IC supply current (ICC)
and the current draw by the peripheral circuitry
connected to VCC (Ip) the excess current is shunted to
VEE via LN.
The regulated voltage on the line terminal (VLN) can
be calculated as:
VLN = Vref + ISLPE x R9
VLN = Vref + ((Iline - ICC - 0.5 x 10-3 A)-Ip) x R9
SLS
System Logic
Semiconductor




PDF 파일 내의 페이지 : 총 9 페이지

제조업체: System Logic Semiconductor

( sls )

SL1062A data

데이터시트 다운로드
:

[ SL1062A.PDF ]

[ SL1062A 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


SL1062A

Low Voltage Transmission Circuit with Dialler Interface - System Logic Semiconductor