파트넘버.co.kr M25P10 데이터시트 PDF


M25P10 반도체 회로 부품 판매점

1 Mbit Low Voltage Paged Flash Memory With 20 MHz Serial SPI Bus Interface



STMicroelectronics 로고
STMicroelectronics
M25P10 데이터시트, 핀배열, 회로
M25P10
1 Mbit Low Voltage Paged Flash Memory
With 20 MHz Serial SPI Bus Interface
PRELIMINARY DATA
s 1 Mbit PAGED Flash Memory
s 128 BYTE PAGE PROGRAM IN 3 ms TYPICAL
s 256 Kbit SECTOR ERASE IN 1 s TYPICAL
s BULK ERASE IN 2 s TYPICAL
s SINGLE 2.7 V to 3.6 V SUPPLY VOLTAGE
s SPI BUS COMPATIBLE SERIAL INTERFACE
s 20 MHz CLOCK RATE AVAILABLE
s SUPPORTS POSITIVE CLOCK SPI MODES
s DEEP POWER DOWN MODE (1 µA TYPICAL)
s ELECTRONIC SIGNATURE
s 10,000 ERASE/PROG CYCLES PER SECTOR
s 20 YEARS DATA RETENTION
s –40 TO 85°C TEMPERATURE RANGE
DESCRIPTION
The M25P10 is an 1 Mbit Paged Flash Memory
fabricated with STMicroelectronics High
Endurance CMOS technology. The memory is
accessed by a simple SPI bus compatible serial
interface. The bus signals are a serial clock input
(C), a serial data input (D) and a serial data output
(Q).
The device connected to the bus is selected when
the chip select input (S) goes low. Data is clocked
in during the low to high transition of clock C, data
8
1
SO8 (MN)
150 mil width
8
1
SO8 (MW)
200 mil width
Figure 1. Logic Diagram
VCC
Table 1. Signal Names
C Serial Clock
D Serial Data Input
Q Serial Data Output
S Chip Select
W Write Protect
HOLD
Hold
VCC Supply Voltage
VSS Ground
D
C
S
W
HOLD
M25P10
VSS
Q
AI03744
June 2000
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
1/21


M25P10 데이터시트, 핀배열, 회로
M25P10
Figure 2. SO Connections
S
Q
W
VSS
M25P10
18
27
36
45
AI03745
VCC
HOLD
C
D
is clocked out during the high to low transition of
clock C
SIGNALS DESCRIPTION
Serial Output (Q)
The output pin is used to transfer data serially out
of the memory. Data is shifted out on the falling
edge of the serial clock.
Serial Input (D)
The input pin is used to transfer data serially into
the device. It receives instructions, addresses,
and the data to be programmed. Input is latched
on the rising edge of the serial clock.
Serial Clock (C)
The serial clock provides the timing of the serial
interface. Instructions, addresses, or data present
at the input pin are latched on the rising edge of
the clock input, while data on the Q pin changes
after the falling edge of the clock input.
Chip Select (S)
When S is high, the memory is deselected and the
Q output pin is at high impedance and, unless an
internal Read, Program, Erase or Write Status
Register operation is underway, the device will be
in the Standby Power mode (this is not the Deep
Power Down mode). S low enables the memory,
placing it in the active power mode. It should be
noted that after power-on, a high to low transition
on S is required prior to the start of any operation.
Hold (HOLD)
The HOLD pin is used to pause serial
communications with a SPI memory without
resetting the serial sequence. To take the Hold
condition into account, the product must be
selected. The HOLD condition is validated by a 0
state on the Hold pin synchronized with the 0 state
on the Clock, as shown in Figure 4. The DeHOLD
condition is validated by a 1 state on the Hold pin
synchronized with the 0 state on the Clock. During
the Hold condition D, Q, and C are at a high
impedance state.
When the memory is under HOLD condition, it is
possible to deselect the device. Then, the protocol
is reset. The memory remains on HOLD as long as
the Hold pin is Low. To restart communication with
the device, it is necessary to both DeHOLD (H =
1) and to SELECT the memory.
Write Protect (W)
This pin is for hardware write protection of the
Status Register (SR); except WIP and WEL bits.
When bit 7 (SRWD) of the status register is 0 (the
initial delivery state); it is possible to write the SR
once the WEL (Write Enable Latch) has been set
with the WREN instruction and whatever is the
status of pin W (high or low).
Table 2. Absolute Maximum Ratings 1
Symbol
Parameter
Value
Unit
TA Ambient Operating Temperature
–40 to 85
°C
TSTG
Storage Temperature
–65 to 150
°C
TLEAD
Lead Temperature during Soldering
SO8: 40 seconds
215
°C
VIO Input and Output Voltage Range (with respect to Ground)
–0.3 to 5.0
V
VCC Supply Voltage Range
–0.6 to 5.0
V
VESD
Electrostatic Discharge Voltage (Human Body model) 2
2000
V
Note: 1. Except for the rating “Ambient Operating Temperature Range”, stresses above those listed in this table may cause permanent
damage to the device. These are stress ratings only, and operation of the device at these or any other conditions above those
indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the ST SURE Program and other relevant quality documents.
2. MIL-STD-883C, 3015.7 (100 pF, 1500 )
2/21




PDF 파일 내의 페이지 : 총 21 페이지

제조업체: STMicroelectronics

( stm )

M25P10 data

데이터시트 다운로드
:

[ M25P10.PDF ]

[ M25P10 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


M25P10

1 Mbit Low Voltage Paged Flash Memory With 20 MHz Serial SPI Bus Interface - STMicroelectronics



M25P10-A

1 Mbit/ Low Voltage/ Serial Flash Memory With 25 MHz SPI Bus Interface - STMicroelectronics



M25P10A

1Mb 3V Serial Flash Embedded Memory - Micron



M25P128

128 Mbit (Multilevel) Low Voltage Serial Flash Memory With 50MHz SPI Bus Interface - ST Microelectronics



M25P128

serial flash memory - Numonyx



M25P16

16 Mbit/ Low Voltage/ Serial Flash Memory With 50 MHz SPI Bus Interface - STMicroelectronics



M25P16

Flash Memory - Numonyx



M25P16

Flash Embedded Memory - Micron



M25P16-V6D11

Flash Embedded Memory - Micron