파트넘버.co.kr VMIVME-4905 데이터시트 PDF


VMIVME-4905 반도체 회로 부품 판매점

High Power Digital-to-Synchro/Resolver Converter Board



VMIC 로고
VMIC
VMIVME-4905 데이터시트, 핀배열, 회로
This product is not recommended for new designs. This specification is
not being maintained. Some options may no longer be available and some
information may be obsolete.
VMIVME-4905
High Power Digital-to-Synchro/Resolver Converter Board
14-bit converter with an accuracy as high as ±1 arc minute
(±4 arc minutes is standard)
3- or 4-wire output for driving synchros or resolvers
Internal transformers (400 Hz options)
Front panel fail LED
Amp D-type (no. 206584-1)
5 VA, 2 VA (transformer output), or 0.024 VA options
Nonprivileged or supervisory short I/O
Supports off-line and on-line fault detection and isolation
Compatible with Intelligent I/O Controllers
DESCRIPTION — The VMIVME-4905, a
digital-to-synchro or resolver converter (DSC/DRC) board,
utilizes the NATEL-HSDR 2514 converter module. It
www.DataSheest4uUpp.coormts a wide variety of options which are supported by
configuring jumpers on the basic printed circuit board and by
installing optional parts (see the Ordering Options). The
VMIVME-4905 board, with supported Built-in-Test VMIC
hardware, features both offline and online fault detection and
isolation. The Built-in-Test features require a VMIC
quad-channel synchro-to-digital converter (SDC) board
(VMIVME-4911) or a single channel SDC board
(VMIVME-4910) and a standard synchro test backplane
(SRTbus™) installed in the P2 position of a standard VME
chassis (refer to VMIC’s Synchro/Resolver (Built-in-Test)
Subsystem Configuration Guide, Document No.
825-000000-004). The board accepts a 14-bit digital output
word (shaft angle), a reference excitation voltage, and
produces a synchro or resolver output.
The board is ideally suited for computer-based systems
in which digital information is processed, such as simulators,
robotics, and other control-oriented systems. The DSC/DRC
is provided with several options and is capable of interfacing
with most standard synchro or resolver devices.
FUNCTIONAL CHARACTERISTICS
Compatibility: VMEbus specification compatible.
Double height form factor.
Output Connector Type: AMP no. 206584-1
Output Organization: Two ports, 16 bits wide.
Addressable to any address within short supervisory or
short nonprivileged I/O map.
Address Modifier Codes: Jumper selectable for short
supervisory or short nonprivileged I/O access. Factory
configured for short supervisory I/O access.
Addressing Scheme: Two ports individually
addressable on 8- or 16-bit boundaries. Two
eight-position DIP switches provide unlimited short data
I/O address map selection.
Ordering Options
September 12, 2000 800-004905-000 G
VMIVME-4905
High Power Option
for DSC/DRC Boards 1
with Built-in-Test*
Dual or
Single
Ref.
Input 2
Signal
Output
(RMS)***
Freq.
(Hz) 3 VA
Board
Output
Type
ABC
Option No.
4** 2** 1.5** 1**
Single 26 V ±10% 11.8 V DC to 1 K 5.0 Synchro 323 324 N/A 325
Single 26 V ±10% 6.81 V DC to 1 K 5.0 Resolver 333 334 N/A 335
Dual
26 V ±10% 11.8 V DC to 1 K 5.0 Synchro 423 424 N/A 425
Dual
26 V ±10% 6.81 V DC to 1 K 5.0 Resolver 433 434 N/A 435
Single
26 V ±10% 11.8 V
400 2.0 Synchro w/ 746 N/A N/A N/A
Trans.
Dual
26 V ±10% 11.8 V
400 2.0 Synchro w/ 846 N/A N/A N/A
Trans.
Single
40 V ±10% 40 V ±14% 512 2.0 Resolver w/ 556 N/A N/A N/A
Trans.
Dual
40 V ±10% 40 V ±14% 512 2.0 Resolver w/ 656 N/A N/A N/A
Trans.
* Built-in-Test requires one synchro/resolver-to-digital converter board for
wrap-back testing of the digital-to-synchro/resolver converter board. Refer to the VMIC
Synchro/Resolver (Built-in-Test) Subsystem Configuration Guide (Document No.
825-000000-004) for a detailed discussion.
** Reference to accuracy
4 = ±4 arc minutes (standard stock item)
2 = ±2 arc minutes (long lead time is typical)
1.5 = ±1.5 arc minutes (long lead time is typical)
1 = ±1 arc minute (long lead time is typical)
*** Contact VMIC for availability of transformer-coupled outputs and higher voltages.
Notes
1. All synchro/resolver boards require external ±15 V power supplies. Power and
reference inputs can be connected to P2 or P3 (front panel). Power input connectors
are available on VMIC's synchro/resolver backplane (SRTbus).
2. The reference input voltage can be jumper-selectable (by the user) for 1.3, 26, or
115 VRMS. Contact VMIC for other reference input voltages.
3. To 10 kHz with reduced accuracy.
Connector Data
Compatible Cable Connector
Strain Relief Kit
PC Board Header Connector
AMP 747322-2
Type D
AMP 206584-1
For Ordering Information, Call:
1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859
E-mail: [email protected] Web Address: www.vmic.com
Copyright © January 1986 by VMIC
Specifications subject to change without notice.
VMIC • 12090 South Memorial Parkway • Huntsville, Alabama 35803-3308
1


VMIVME-4905 데이터시트, 핀배열, 회로
Ordering Options
September 12, 2000 800-004905-000 G
VMIVME-4905
Low Power Option
for DSC/DRC Boards 1
with Built-in-Test*
Dual or
Single
Ref.
Input 2
Signal
Output
(RMS)***
Freq.
(Hz) 3 VA
Board
Output
Type
Option No.
4** 2** 1.5** 1**
Single 26 V ±10% 11.8 V DC to 1 K .024 Synchro 320 321 N/A 322
Single 26 V ±10%
www.DataSheet4DUu.aclom 26 V ±10%
Dual 26 V ±10%
6.81 V
11.8 V
6.81 V
DC to 1 K .024
DC to 1 K .024
DC to 1 K .024
Resolver
Synchro
Resolver
330 331 N/A 332
420 421 N/A 422
430 431 N/A 432
Single 5 V ±8% 11.8 V DC to 1 K .024 Synchro 300 301 N/A 302
Single 5 V ±8% 6.81 V DC to 1 K .024 Resolver 310 311 N/A 312
Dual
5 V ±8% 11.8 V DC to 1 K .024 Synchro 400 401 N/A 402
Dual
40 V ±8% 6.81 V DC to 1 K .024 Resolver 410 411 N/A 412
* Built-in-Test requires one synchro/resolver-to-digital converter board for
wrap-back testing of the digital-to-synchro/resolver converter board. Refer to the VMIC
Synchro/Resolver (Built-in-Test) Subsystem Configuration Guide (Document No.
825-000000-004) for a detailed discussion.
** Reference to accuracy
4 = ±4 arc minutes (standard stock item)
2 = ±2 arc minutes (long lead time is typical)
1.5 = ±1.5 arc minutes (long lead time is typical)
1 = ±1 arc minute (long lead time is typical)
*** Line-to-Line voltage for synchro outputs.
Notes
1. All synchro/resolver boards require external ±15 V power supplies. Power and
reference inputs can be connected to P2 or P3 (front panel). Power input connectors
are available on VMIC's synchro/resolver backplane (SRTbus).
2. The 26 V reference input can be jumper-selectable (by the user) for 1.3, 26, or
115 VRMS. Contact VMIC for other reference input voltages.
3. To 10 kHz with reduced accuracy.
Connector Data
Compatible Cable Connector
Strain Relief Kit
PC Board Header Connector
AMP 747322-2
Type D
AMP 206584-1
For Ordering Information, Call:
1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859
E-mail: [email protected] Web Address: www.vmic.com
Copyright © January 1986 by VMIC
Specifications subject to change without notice.
Fail LED: A front panel Fail LED (red) is provided that
is illuminated at power up and extinguished under
program control upon successful completion of
user-defined diagnostics.
Power Requirements:
5 and 2 VA
Options
+5 V at 2 A
+15 V at 2.6 A4
-15 V at 2.6 A4
VMIVME-4905
Low Power
Options
+5 V at 2 A
+15 V at 50 mA4
-15 V at 50 mA4
Notice — If this board is used with VMIC’s Intelligent
I/O Controller (IIOC) product line (VMIVME-9015,
-9016A, -9017, -9027, -9065, -9066, -9067, and -9068), a
quad-channel S/D board (VMIVME-4911) and SRTbus is
required for Built-in-Test. The IIOC firmware is not
compatible with the VMIVME-4910.
Built-in-Test DESCRIPTION — The VMIVME-4905
supports fault detection and isolation when used with the
VMIC SRTbus and the model VMIVME-4911. The SRTbus
is a synchro/resolver test bus that utilizes the user I/O pins on
the P2 VMEbus connector. Programming the proper control
bits in each output word of the VMIVME-4905 allows field
disconnect and/or real-time loopback testing via the SRTbus
and the VMIVME-4911. The user should refer to the
VMIVME-4905 functional block diagram and the
synchro/resolver (Built-in-Test) Subsystem Configuration
Guide for a thorough understanding of the Built-in-Test
operation.
Notice — The VMIVME-4905 is an enhanced version of
the VMIVME-4900 series with different programming
requirements. The VMIVME-4905 is not software
compatible with the VMIVME-4900 series.
Caution — When driving instruments with one or more
phase connections grounded, transformer isolation is
required.
4. External ±15 V power supply required.
PHYSICAL/ENVIRONMENTAL
Temperature Range: 0 to +55 °C, operating
-20 to +85 °C, storage
Relative Humidity Range: 20 to 80 percent,
noncondensing
Cooling: Forced air cooling is required for the 5 and
2 VA options
2 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 • FAX (256) 882-0859




PDF 파일 내의 페이지 : 총 3 페이지

제조업체: VMIC

( vmic )

VMIVME-4905 converter

데이터시트 다운로드
:

[ VMIVME-4905.PDF ]

[ VMIVME-4905 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


VMIVME-4905

High Power Digital-to-Synchro/Resolver Converter Board - VMIC