|
|
PDF PG001 Data sheet ( Hoja de datos )
| Número de pieza | PG001 | |
| Descripción | PARALLEL-TO-SERIAL DATA CONVERTER | |
| Fabricantes | Allegro MicroSystems | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PG001 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
RESET 1
CLOCK IN 2
CCW/CW 3
NOT USABLE 4
NOT USABLE 5
MODE
SELECT. .1
MODE
SELECT. 2.
6
7
GROUND 8
PG001M
V DD 16
15
CONTROL
SUPPLY
VECTOR
CONTROL
14 CLOCK OUT
13 STROBE
12 NO
CONNECT.
11 SERIAL
DATA A
10 SERIAL
DATA B
9 MONITOR
Dwg. PK-009
PARALLEL-TO-SERIAL
DATA CONVERTER
The PG001M CMOS IC converts parallel-data signals from a low-
cost, 8-bit microprocessor or microcontroller into a serial-data format
compatible with the SLA7042M and SLA7044M power multi-chip
modules to drive unipolar PWM, high-current stepper motors. The
converter provides for five basic modes of operation:
1) normal, two-phase, full step (100% torque vector),
2) two-phase 'boosted' torque (141% torque vector),
3) half-step, constant torque operation (using a 2-1-2 output switching),
4) quarter-stepping utilizing ratioed currents for constant torque, and
5) microstepping (1/8th steps) for quiet, smooth, resonance-free motor
performance.
The PG001M is supplied in a low-cost 16-pin dual in-line plastic
package. It is rated for continuous operation over the temperature
range of -20°C to +85°C.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VDD .................... 7.0 V
Input Voltage Range,
VI ................ -0.5 V to VDD + 0.5 V
Input Current, II ....................... ±10 mA
Output Voltage Range,
VO ............... -0.5 V to VDD + 0.5 V
Output Current, IO ................... ±15 mA
Operating Temperature Range,
TA .......................... -20°C to +85°C
Storage Temperature Range,
TS ........................ -40°C to +150°C
CAUTION: CMOS devices have input static
protection but are susceptible to damage if
exposed to extremely high static electrical
charges.
FEATURES
s Intended For Use With SLA7042M or SLA7044M
Microstepping, Unipolar PWM, High-Current Motor Drivers
s Supports Five Stepper-Motor Operating Modes
s µP-Compatible Inputs
Always order by complete part number, PG001M .
™
1 page  
PG001M
PARALLEL-TO-SERIAL
DATA CONVERTER
PG001M DESCRIPTION AND OPERATION
The PG001M is a CMOS step-motor control IC that
converts parallel-input signals from a microprocessor (µP,
or microcontroller, µC) to the serial-input data format
required for control of an SLA7042M or SLA7044M
microstepping, unipolar PWM, high-current motor driver.
This control IC offers five basic modes of motor operation:
1) normal 2-phase, full-step (100% torque vector);
2) 2-phase, full-step 'boosted' torque (141% vector);
3) 1/2-step, constant torque operation
(i.e., 2-1-2 switching);
4) 1/4-step operation with current-ratioed constant
torque; and
5) smooth microstepping operation (1/8th step) for
resonance-free motor performance (constant torque
with eight output current ratios).
Three inputs (VC, MS1, and MS2) control these five
operational modes (as shown in figure 1); this enables
designers to change the drive method during movement to
realize optimal performance.
Initially, at start-up, the high-torque mode can provide
141% torque (the resulting vector of both motor windings
at 100% current). This enhances rapid acceleration (and
deceleration). Switching to quarter-stepping or
microstepping (after initial, startup acceleration) offers
smooth, resonance-free operation during the ramp-up
interval. The transition to quarter- or microstepping
should occur before the increasing step rate approaches the
motor resonance frequency (usually 100 to 200 Hz).
The modes of operation and current-control truth table
are listed on page 2; and there are two full-step, 2-phase
(2-2) operating modes. The VECTOR CONTROL input
(VC) can only be changed when MONITOR (MO, a
readback pin) is LOW and the PG001M is operating in the
full-step mode. Starting (or stopping) the step motor with
VC HIGH delivers the highest torque (141%) from the
motor, and is the extension of two outputs ON at 71.4%.
This 'half-step' rotor position corresponds to the state when
MO is LOW, and switching the control inputs to another
operating mode is allowed.
The PG001M accepts logic signals from the µP and
converts these into the proper serial-data format required
to control the serial-data input lines of the SLA7042M or
SLA7044M microstepping power modules. The five
A
AB AB
BB
A
ONE-PHASE, FULL-STEP MODE
(WITHOUT PG001M)
AB AB
AB AB
TWO-PHASE, FULL-STEP MODE
(MS1 = L, MS2 = L, VC = L)
A
AB AB
BB
AB AB
TWO-PHASE, FULL-STEP MODE
MAXIMUM TORQUE (141%)
(MS1 = L, MS2 = L, VC = H)
A
AB AB
AB AB
A
1/2-STEP MODE
CONSTANT TORQUE
(MS1 = H, MS2 = L, VC = X)
A
AB AB
B BB B
AB AB
A
1/4-STEP MODE
(MS1 = L, MS2 = H, VC = X)
AB AB
A
1/8-STEP MODE
(MS1 = H, MS2 = H, VC = X)
Dwg. OP-005
NOTE – Mode change only allowed at half-step positions (refer to
upper right figure).
Figure 1 — Current/Displacement Vectors
control inputs determine the various modes of operation.
The CLOCKOUT, SERIAL DATAA, SERIAL DATAB, and
STROBE to the SLA7042/44M are synchronized to the
CLOCKIN of the PG001M; and the CLOCKIN frequency is
eight times the step rate (more to follow on the signal/
timing relationships).
The internal logic and oscillator combine to convert
the parallel input signals to 'bursts' of serial data from the
5 Page 
PG001M
PARALLEL-TO-SERIAL
DATA CONVERTER
16
0.280
0.240
Dimensions in Inches
(controlling dimensions)
9
0.014
0.008
0.430
MAX
0.300
BSC
1
0.070
0.045
0.210
MAX
0.015
MIN
0.022
0.014
16
7.11
6.10
0.775
0.735
0.100
BSC
8
0.005
MIN
0.150
0.115
Dimensions in Millimeters
(for reference only)
9
Dwg. MA-001-16A in
0.355
0.204
10.92
MAX
7.62
BSC
1
1.77
1.15
5.33
MAX
19.68
18.67
2.54
BSC
8
0.13
MIN
0.39
MIN
3.81
2.93
0.558
0.356
NOTES:1. Lead thickness is measured at seating plane or below.
2. Lead spacing tolerance is non-cumulative.
3. Exact body and lead configuration at vendor’s option within limits shown.
Dwg. MA-001-16A mm
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet PG001.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PG001 | Serial Signal Generator IC for SLA7042M and SLA7044M |  Sanken electric |
| PG001 | PARALLEL-TO-SERIAL DATA CONVERTER | Allegro MicroSystems |
| PG001M | Serial Signal Generator IC for SLA7042M and SLA7044M | Sanken electric |
| PG001M | PARALLEL-TO-SERIAL DATA CONVERTER | Allegro MicroSystems |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |