파트넘버.co.kr M82C288 데이터시트 PDF


M82C288 반도체 회로 부품 판매점

BUS CONTROLLER FOR M80286 PROCESSORS



Intel 로고
Intel
M82C288 데이터시트, 핀배열, 회로
M82C288
BUS CONTROLLER FOR M80286 PROCESSORS
(M82C288-10 M82C288-8 M82C288-6)
Military
Y Provides Commands and Controls for
Local and System Bus
Y Wide Flexibility in System
Configurations
Y Implemented in High Speed CHMOS III
Technology
Y Fully Compatible with the HMOS
M82288
Y Fully Static Device
Y Single a5V Supply
Y Available in 20 Pin Cerdip Package
(See Packaging Spec Order 231369)
The Intel M82C288 Bus Controller is a 20-pin CHMOS III component for use in M80C286 microsystems The
M82C288 is fully compatible with its predecessor the HMOS M82288 The bus controller is fully static and
supports a low power mode The bus controller provides command and control outputs with flexible timing
options Separate command outputs are used for memory and I O devices The data bus is controlled with
separate data enable and direction control signals
Two modes of operation are possible via a strapping option MULTIBUS Compatible bus cycles and high
speed bus cycles
20 Pin Cerdip Package
Figure 1 M82C288 Block Diagram
271077 – 1
271077 – 2
Figure 2 M82C288 Pin
Configuration
November 1991
Order Number 271077-006


M82C288 데이터시트, 핀배열, 회로
M82C288
Table 1 Pin Description
The following pin function descriptions are for the M82C288 bus controller
Symbol Type
Name and Function
CLK I SYSTEM CLOCK provides the basic timing control for the M82C288 in an M80286
microsystem Its frequency is twice the internal processor clock frequency The falling edge
of this input signal establishes when inputs are sampled and command and control outputs
change
S0 S1
I BUS CYCLE STATUS starts a bus cycle and along with M IO defines the type of bus
cycle These inputs are active LOW A bus cycle is started when either S1 or S0 is sampled
LOW at the falling edge of CLK Setup and hold times must be met for proper operation
M80286 Bus Cycle Status Definition
M IO S1 S0
Type of Bus Cycle
0 0 0 Interrupt Acknowledge
0 0 1 I O Read
0 1 0 I O Write
0 1 1 None Idle
1 0 0 Halt or Shutdown
1 0 1 Memory Read
1 1 0 Memory Write
1 1 1 None Idle
M IO
I MEMORY OR I O SELECT determines whether the current bus cycle is in the memory
space or I O space When LOW the current bus cycle is in the I O space Setup and hold
times must be met for proper operation
MB I MULTIBUS MODE SELECT determines timing of the command and control outputs When
HIGH the bus controller operates with MULTIBUS I compatible timings When LOW the
bus controller optimizes the command and control output timing for short bus cycles The
function of the CEN AEN input pin is selected by this signal This input is typically a
strapping option and not dynamically changed
CENL
I COMMAND ENABLE LATCHED is a bus controller select signal which enables the bus
controller to resopnd to the current bus cycle being initiated CENL is an active HIGH input
latched internally at the end of each TS cycle CENL is used to select the appropriate bus
controller for each bus cycle in a system where the CPU has more than one bus it can use
This input may be connected to VCC to select this M82C288 for all transfers No control
inputs affect CENL Setup and hold times must be met for proper operation
CMDLY
I COMMAND DELAY allows delaying the start of a command CMDLY is an active HIGH
input If sampled HIGH the command output is not activated and CMDLY is again sampled
at the next CLK cycle When sampled LOW the selected command is enabled If READY is
detected LOW before the command output is activated the M82C288 will terminate the bus
cycle even if no command was issued Setup and hold times must be satisified for proper
operation This input may be connected to GND if no delays are required before starting a
command This input has no effect on M82C288 control outputs
READY
I READY indicates the end of the current bus cycle READY is an active LOW input
MULTIBUS I mode requires at least one wait state to allow the command outputs to
become active READY must be LOW during reset to force the M82C288 into the idle state
Setup and hold times must be met for proper operation The M82C284 drives READY LOW
during RESET
2




PDF 파일 내의 페이지 : 총 20 페이지

제조업체: Intel

( intel )

M82C288 controller

데이터시트 다운로드
:

[ M82C288.PDF ]

[ M82C288 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


M82C288

BUS CONTROLLER FOR M80286 PROCESSORS - Intel



M82C288-10

BUS CONTROLLER FOR M80286 PROCESSORS - Intel



M82C288-6

BUS CONTROLLER FOR M80286 PROCESSORS - Intel



M82C288-8

BUS CONTROLLER FOR M80286 PROCESSORS - Intel