|
Hirose Electric |
2.54mm Pitch Miniature Connector for Flexible Board
FH1 Series
sFeatures
1. 2.54mm FPC and FFC Connector
The contact pitch is 2.54mm.
2. Contact Reliability
This connector assures high contact reliability for high voltage
contact.
3. Eighteen Types of Contact Numbers
This connector consists of 18 kinds of 8, 9, 10, 11, 12, 13, 14,
15, 15, 17, 18, 19, 20, 21, 22, 27, and 29 contacts.
sApplications
HDD, facsimiles, printers, VTR, etc.
sProduct Specifications
Rating
Rated Current: 1A
Operating Temperature Range:_40~+85ç (Note 1) Storage Temperature Range:_10~+60ç (Note 2)
Operating Humidity Range:Relative humidity, 90% max. Storage Humidity Range: Relative humidity, 90% max.
Rated Voltage: 200V AC
(Not dewed)
(Not dewed)
Applicable FPC
t=0.13~0.3 Tin plating
Item
Specification
Condition
1. Insulation Resistance 5000Mø min.
Measured at 500V DC
2. Withstand voltage
Neither short or breakdown should occur.
500V AC for 1 minute
3. Contact Resistance
20mømax.
π FPC conductor resistance included
Measured at DC 1A
Contact resistance : 40mø max.
4. Mechanical operation
No part should be broken, cracked or loosened
30 cycles
5. Vibration
No part should be broken, cracked or loosened
Frequency: 10~55Hz and full amplitude 1.50mm in 3 directions for 2 hours, respectively
6. Shock
No part should be broken, cracked or loosened
Acceleration: 490m/S2, duration: 11ms, sine half-wave: in 3 directions for 3 times, respectively
7. Moisture Resistance in Steady State Insulation resistance: 500Mø min.
Exposed to temperature 40ç and humidity 90~95% for 96 hours
5 cycles under conditions as follows;
8. Temperature Cycle No part should be broken, cracked or loosened
Temperature: _55ç¡+5~+35¡85¡+5~+35ç
Time: 30¡10~15¡ 30~10~15 minutes
9.Resistance to Soldering heat Neither appearance should be deformed nor contact remarkably loosened. Automatic soldering: 260çœ for 10 seconds
Note 1. Temperature rise included when energized
Note 2. This storage indicates a long-term storage state for the unused product before board mounted.
The operating temperature and humidity ranges are applied to the non-energized state after the connector has been installed
in the board.
Note 3. The above standards represent this series. The individual formal agreement should be based on the "Specification".
D2
sMaterial
Part
Insulator
Contact
Material
PBT
Phosphor bronze
Finish
Black
Tin plating
Remarks
UL94V-0
–––––––
sOrdering Information
Please determine the specific product. If needed, please select and order the product from the product No. as listed on
catalog page D4 and D5.
FH 1 - 17 S -2.54 DS
qw er t y
q Series Name : FH
r Contact alignment : Single
w Series No.
:1
t Contacts Pitch : 2.54mm
e Number of Contacts : 6, 8, 9, 10, 11, 12, 13, 14, 15, y Contact Type : DS : Right angle type
16, 17, 18, 19, 20, 21, 22, 27, 29
DSA : Straight type
sFPC · FFC Dimensions
Unit: mm
Number of Contacts
5 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 27 29
Size
A 10.16 17.78 20.32 22.86 25.40 27.94 30.48 33.02 35.56 38.10 40.64 43.18 45.72 48.26 50.80 53.34 66.04 71.12
B 15.29 22.91 25.45 27.99 30.53 33.07 35.61 38.15 40.69 43.23 45.77 48.31 50.85 53.39 55.93 58.47 69.90 76.25
D3
|