|
|
PDF TU24C64CP3 Data sheet ( Hoja de datos )
| Número de pieza | TU24C64CP3 | |
| Descripción | CMOS IC 2-WIRE BUS 64K ELECTRICALLY ERASABLE PROGRAMMABLE ROM 8K X 8 BIT EEPROM | |
| Fabricantes | ETC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TU24C64CP3 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Turbo IC, Inc.
24C64
CMOS I²C 2-WIRE BUS
64K ELECTRICALLY ERASABLE PROGRAMMABLE ROM
8K X 8 BIT EEPROM
FEATURES :
• Extended Power Supply Voltage
Single Vcc for Read and Programming
(Vcc = 2.7 V to 5.5 V)
• Low Power (Isb = 2µa @ 5.5 V)
• Extended I²C Bus, 2-Wire Serial Interface
• Support Byte Write and Page Write (32 Bytes)
• Automatic Page write Operation (maximum 10 ms)
Internal Control Timer
Internal Data Latches for 32 Bytes
• Hardware Data Protection by Write Protect Pin
• High Reliability CMOS Technology with EEPROM Cell
Endurance : 1,000,000 Cycles
Data Retention : 100 Years
DESCRIPTION:
The Turbo IC 24C64 is a serial 64K EEPROM fabricated
with Turbo’s proprietary, high reliability, high performance
CMOS technology. It’s 64K of memory is organized as 8,192
x 8 bits. The memory is configured as 256 pages with each
page containing 32 bytes. This device offers significant ad-
vantages in low power and low voltage applications.
The Turbo IC 24C64 uses the extended I²C addressing pro-
tocol and 2-wire serial interface which includes a bidirec-
tional serial data bus synchronized by a clock. It offers a
flexible byte write and a faster 32-byte page write. The data
in the upper quadrant of memory can be protected by a
write protect pin.
PIN DESCRIPTION
A0
A1
A2
GND
18
27
36
45
VCC
WP
SCL
SDA
8 pin SOIC
PIN DESCRIPTION
A0
A1
A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
8 pin PDIP
The Turbo IC 24C64 is assembled in either a 8-pin PDIP or
8-pin SOIC package. Pin #1 (A0), #2 (A1), and #3 (A2) are
device address input pins which are hardwired by the user.
Pin #4 is the ground (Vss). Pin #5 is the serial data (SDA)
pin used for bidirectional transfer of data. Pin #6 is the serial
clock (SCL) input pin. Pin #7 is the write protect (WP) input
pin, and Pin #8 is the power supply (Vcc) pin.
All data is serially transmitted in bytes (8 bits) on the SDA
bus. To access the Turbo IC 24C64 (slave) for a read or
write operation, the controller (master) issues a start condi-
tion by pulling SDA from high to low while SCL is high. The
master then issues the device address byte which consists
of 1010 (A2) (A1) (A0) (R/W). The 4 most significant bits
(1010) are a device type code signifying an EEPROM de-
vice. The A[2:0] bits represent the input levels on the 3 de-
vice address input pins. The read/write bit determines
whether to do a read or write operation. After each byte is
transmitted, the receiver has to provide an acknowledge by
pulling the SDA bus low on the ninth clock cycle. The ac-
knowledge is a handshake signal to the transmitter indicat-
ing a successful data transmission.
DEVICE ADDRESSES (A2-A0)
The address inputs are used to define the 3 least
significant bits of the 7-bit device address code -
1010 (A2) (A1) (A0). These pins can be con-
nected either high or low. A maximum of eight
Turbo IC 24C64 can be connected in parallel,
each with a unique device address. When these
pins are left unconnected, the device addresses
are interpreted as zero.
WRITE PROTECT (WP)
When the write protect input is connected to Vcc,
the upper quadrant of memory (1800-1FFFH) is
protected against write operations. For normal
write operation, the write protect pin should be
grounded. When this pin is left unconnected, WP
is interpreted as zero.
SERIAL DATA (SDA)
SDA is a bidirectional pin used to transfer data
in and out of the Turbo IC 24C64. The pin is an
open-
1
drain output. A pullup resistor must be connected
from SDA to Vcc.
SERIAL CLOCK (SCL)
The SCL input synchronizes the data on the SDA
bus. It is used in conjunction with SDA to define
the start and stop conditions. It is also used in
conjunction with SDA to transfer data to and from
the Turbo IC 24C64.
1 page  
Turbo IC, Inc.
24C64
Device Address
1 0 1 0 A2 A1 A0 R/W
MSB
LSB
Byte Write
SW
TR
AI
R DEVICE T
FIRST
SECOND
T ADDRESS E WORD ADDRESS WORD ADDRESS
SDA LINE
***
M
L RA
M
A
S
S /C
S
C
B
B WK
B
K
LA
SC
BK
DATA
S
T
O
P
A
C
K
Page Write
SDA LINE
SW
TR
AI
R DEVICE T
FIRST
SECOND
T ADDRESS E WORD ADDRESS (n) WORD ADDRESS (n)
***
M
L RA
M
A
S
S /C
S
C
B
B WK
B
K
LA
SC
BK
DATA (n)
// DATA (n + x)
//
A
C
K
S
T
O
P
A
C
K
* = Don't care bits
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet TU24C64CP3.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TU24C64CP2 | CMOS IC 2-WIRE BUS 64K ELECTRICALLY ERASABLE PROGRAMMABLE ROM 8K X 8 BIT EEPROM | ETC |
| TU24C64CP3 | CMOS IC 2-WIRE BUS 64K ELECTRICALLY ERASABLE PROGRAMMABLE ROM 8K X 8 BIT EEPROM | ETC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |