파트넘버.co.kr A290011TV-70 데이터시트 PDF


A290011TV-70 반도체 회로 부품 판매점

128K X 8 Bit CMOS 5.0 Volt-only/ Boot Sector Flash Memory



AMIC Technology 로고
AMIC Technology
A290011TV-70 데이터시트, 핀배열, 회로
A29001/290011 Series
Preliminary
128K X 8 Bit CMOS 5.0 Volt-only,
Boot Sector Flash Memory
Features
n 5.0V ± 10% for read and write operations
n Access times:
- 55/70/90 (max.)
n Current:
- 20 mA typical active read current
- 30 mA typical program/erase current
- 1 µA typical CMOS standby
n Flexible sector architecture
- 8 Kbyte/ 4 KbyteX2/ 16 Kbyte/ 32 KbyteX3 sectors
- Any combination of sectors can be erased
- Supports full chip erase
- Sector protection:
A hardware method of protecting sectors to prevent
any inadvertent program or erase operations within
that sector
n Top or bottom boot block configurations available
n Embedded Erase Algorithms
- Embedded Erase algorithm will automatically erase the
entire chip or any combination of designated sectors
and verify the erased sectors
- Embedded Program algorithm automatically writes and
verifies bytes at specified addresses
n Typical 100,000 program/erase cycles per sector
n 20-year data retention at 125°C
- Reliable operation for the life of the system
n Compatible with JEDEC-standards
- Pinout and software compatible with single-power-
supply Flash memory standard
- Superior inadvertent write protection
n Data Polling and toggle bits
- Provides a software method of detecting completion of
program or erase operations
n Erase Suspend/Erase Resume
- Suspends a sector erase operation to read data from,
or program data to, a non-erasing sector, then
resumes the erase operation
n Hardware reset pin (RESET )
- Hardware method to reset the device to reading array
data (not available on A290011)
n Package options
- 32-pin P-DIP, PLCC, or TSOP (Forward type)
General Description
The A29001 is a 5.0 volt-only Flash memory organized as
131,072 bytes of 8 bits each. The A29001 offers the RESET
function, but it is not available on A290011. The 128 Kbytes of
data are further divided into seven sectors for flexible sector
erase capability. The 8 bits of data appear on I/O0 - I/O7 while
the addresses are input on A0 to A16. The A29001 is offered in
32-pin PLCC, TSOP, and PDIP packages. This device is
designed to be programmed in-system with the standard
system 5.0 volt VCC supply. Additional 12.0 volt VPP is not
required for in-system write or erase operations. However, the
A29001 can also be programmed in standard EPROM
programmers.
The A29001 has the first toggle bit, I/O6, which indicates
whether an Embedded Program or Erase is in progress, or it is
in the Erase Suspend. Besides the I/O6 toggle bit, the A29001
has a second toggle bit, I/O2, to indicate whether the
addressed sector is being selected for erase. The A29001 also
offers the ability to program in the Erase Suspend mode. The
standard A29001 offers access times of 55, 70 and 90 ns
allowing high-speed microprocessors to operate without wait
states. To eliminate bus contention the device has separate
chip enable ( CE ), write enable ( WE ) and output enable ( OE )
controls.
The device requires only a single 5.0 volt power supply for both
read and write functions. Internally generated and regulated
voltages are provided for the program and erase operations.
The A29001 is entirely software command set compatible with
the JEDEC single-power-supply Flash standard. Commands
are written to the command register using standard
microprocessor write timings. Register contents serve as input
to an internal state-machine that controls the erase and
programming circuitry. Write cycles also internally latch
addresses and data needed for the programming and erase
operations. Reading data out of the device is similar to reading
from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase
command sequence. This initiates the Embedded Erase
algorithm - an internal algorithm that automatically
preprograms the array (if it is not already programmed) before
executing the erase operation. During erase, the device
automatically times the erase pulse widths and verifies proper
erase margin.
PRELIMINARY (August, 2001, Version 0.3)
1
AMIC Technology, Inc.


A290011TV-70 데이터시트, 핀배열, 회로
A29001/A290011 Series
The host system can detect whether a program or erase
operation is complete by reading the I/O7 (Data Polling) and
I/O6 (toggle) status bits. After a program or erase cycle has
been completed, the device is ready to read array data or
accept another command.
The sector erase architecture allows memory sectors to be
erased and reprogrammed without affecting the data contents
of other sectors. The A29001 is fully erased when shipped
from the factory.
The hardware sector protection feature disables operations for
both program and erase in any combination of the sectors
Pin Configurations
of memory. This can be achieved via programming
equipment.
The Erase Suspend feature enables the user to put erase on
hold for any period of time to read data from, or program data
to, any other sector that is not selected for erasure. True
background erase can thus be achieved.
Power consumption is greatly reduced when the device is
placed in the standby mode.
The hardware RESET pin terminates any operation in
progress and resets the internal state machine to reading
array data (This feature is not available on the A290021).
n DIP
n PLCC
NC on A290011
RESET
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32 VCC
31 WE
30 NC
29 A14
28 A13
27 A8
26 A9
25 A11
24 OE
23 A10
22 CE
21 I/O7
20 I/O6
19 I/O5
18 I/O4
17 I/O3
NC on A290011
A7 5
A6 6
A5 7
A4 8
A3 9
A2 10
A1 11
A0 12
I/O0 13
A29001L/
A290011L
29 A14
28 A13
27 A8
26 A9
25 A11
24 OE
23 A10
22 CE
21 I/O7
n TSOP (Forward type)
A11
A9
A8
A13
A14
NC
WE
VCC
RESET
A16
A15
NC on A290011 A12
A7
A6
A5
A4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A29001V/A290011V
32 OE
31 A10
30 CE
29 I/O7
28 I/O6
27 I/O5
26 I/O4
25 I/O3
24 VSS
23 I/O2
22 I/O1
21 I/O0
20 A0
19 A1
18 A2
17 A3
PRELIMINARY (August, 2001, Version 0.3)
2
AMIC Technology, Inc.




PDF 파일 내의 페이지 : 총 30 페이지

제조업체: AMIC Technology

( amic )

A290011TV-70 cmos

데이터시트 다운로드
:

[ A290011TV-70.PDF ]

[ A290011TV-70 다른 제조사 검색 ]




국내 전력반도체 판매점


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877

[ 홈페이지 ]

IGBT, TR 모듈, SCR, 다이오드모듈, 각종 전력 휴즈

( IYXS, Powerex, Toshiba, Fuji, Bussmann, Eaton )

전력반도체 문의 : 010-3582-2743



일반적인 전자부품 판매점


디바이스마트

IC114

엘레파츠

ICbanQ

Mouser Electronics

DigiKey Electronics

Element14


관련 데이터시트


A290011TV-70

128K X 8 Bit CMOS 5.0 Volt-only/ Boot Sector Flash Memory - AMIC Technology