|
Motorola Semiconductors |
Order this document by TL062/D
Low Power JFET Input
Operational Amplifiers
These JFET input operational amplifiers are designed for low power
applications. They feature high input impedance, low input bias current and
low input offset current. Advanced design techniques allow for higher slew
rates, gain bandwidth products and output swing.
The commercial and vehicular devices are available in Plastic dual in–line
and SOIC packages.
• Low Supply Current: 200 µA/Amplifier
• Low Input Bias Current: 5.0 pA
• High Gain Bandwidth: 2.0 MHz
• High Slew Rate: 6.0 V/µs
• High Input Impedance: 1012 Ω
• Large Output Voltage Swing: ±14 V
• Output Short Circuit Protection
Representative Schematic Diagram
(Each Amplifier)
VCC
Inputs
–
+
J1 J2
+
Q3
Q1 Q2
Q4
D2
C1
Q5
Q7
R3 R4
D1 Output
C2
Q6
R1 R2
R5
VEE
Op Amp
Function
Dual
Quad
ORDERING INFORMATION
Device
Operating
Temperature Range
TL062CD, ACD
TL062CP, ACP
TA = 0° to +70°C
TL062VD
TL062VP
TA = –40° to +85°C
TL064CD, ACD
TL064CN, ACN
TA = 0° to +70°C
TL064VD
TL064VN
TA = –40° to +85°C
Package
SO–8
Plastic DIP
SO–8
Plastic DIP
SO–14
Plastic DIP
SO–14
Plastic DIP
TL062
TL064
LOW POWER JFET INPUT
OPERATIONAL AMPLIFIERS
SEMICONDUCTOR
TECHNICAL DATA
DUAL
8
1
P SUFFIX
PLASTIC PACKAGE
CASE 626
8
1
D SUFFIX
PLASTIC PACKAGE
CASE 751
(SO–8)
PIN CONNECTIONS
Output 1 1
Inputs 1
2–
3+
VEE 4
8 VCC
7 Output 2
6
–
+5
Inputs 2
(Top View)
QUAD
14
1
N SUFFIX
PLASTIC PACKAGE
CASE 646
14
1
D SUFFIX
PLASTIC PACKAGE
CASE 751A
(SO–14)
PIN CONNECTIONS
Output 1 1
Inputs 1 2 * 1
3+
VCC 4
Inputs 2
5
6
+2
–
Output 2 7
14 Output 4
4 * 13
+ 12
Inputs 4
11 VEE
3 + 10
–9
Inputs 3
8 Output 3
(Top View)
MOTOROLA ANALOG IC DEVICE DATA
© Motorola, Inc. 1996
Rev 5
1
TL062 TL064
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Supply Voltage (from VCC to VEE)
VS +36
V
Input Differential Voltage Range (Note 1)
VIDR
±30
V
Input Voltage Range (Notes 1 and 2)
VIR ±15
V
Output Short Circuit Duration (Note 3)
tSC Indefinite sec
Operating Junction Temperature
TJ +150 °C
Storage Temperature Range
Tstg –60 to +150
°C
NOTES: 1. Differential voltages are at the noninverting input terminal with respect to the inverting input
terminal.
2. The magnitude of the input voltage must never exceed the magnitude of the supply or 15 V,
whichever is less.
3. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not
exceeded. (See Figure 1.)
ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = –15 V, TA = 0° to +70°C, unless otherwise noted.)
TL062AC
TL064AC
TL062C
TL064C
Characteristics
Symbol Min Typ Max Min Typ Max
Input Offset Voltage (RS = 50 Ω, VO = 0V)
TA = 25°C
TA = 0° to +70°C
Average Temperature Coefficient for Offset Voltage
(RS = 50 Ω, VO = 0 V)
Input Offset Current (VCM = 0 V, VO = 0 V)
TA = 25°C
TA = 0° to +70°C
Input Bias Current (VCM = 0 V, VO = 0 V)
TA = 25°C
TA = 0° to +70°C
Input Common Mode Voltage Range
TA = 25°C
Large Signal Voltage Gain (RL = 10 kΩ, VO = ±10 V)
TA = 25°C
TA = 0° to +70°C
Output Voltage Swing (RL = 10 kΩ, VID = 1.0 V)
TA = 25°C
TA = 0° to +70°C
Common Mode Rejection
(RS = 50 Ω, VCM = VICR min, VO = 0 V, TA = 25°C)
Power Supply Rejection
(RS = 50 Ω, VCM = 0 V, VO = 0, TA = 25°C)
Power Supply Current (each amplifier)
(No Load, VO = 0 V, TA = 25°C)
VIO
— 3.0 6.0 — 3.0 15
— — 7.5 — — 20
∆VIO/∆T
—
10
—
—
10
—
IIO
IIB
VICR
AVOL
— 0.5 100 — 0.5 200
— — 2.0 — — 2.0
— 3.0 200 — 3.0 200
— — 2.0 — — 10
— +14.5 +11.5 — +14.5 +11
–11.5 –12.0 — –11 –12.0 —
4.0 58
4.0 —
— 3.0 58
— 3.0 —
—
—
VO+
VO–
VO+
VO–
CMR
+10 +14 — +10 +14 —
— –14 –10 — –14 –10
+10 —
— +10 —
—
— — –10 — — –10
80 84 — 70 84 —
PSR
80 86 — 70 86 —
ID — 200 250 — 200 250
Total Power Dissipation (each amplifier)
(No Load, VO = 0 V, TA = 25°C)
PD — 6.0 7.5 — 6.0 7.5
Unit
mV
µV/°C
pA
nA
pA
nA
V
V/mV
V
dB
dB
µA
mW
2 MOTOROLA ANALOG IC DEVICE DATA
|