|
NXP Semiconductors |
BGU7063
Analog controlled high linearity low noise variable gain
amplifier
Rev. 2 — 7 December 2012
Product data sheet
1. Product profile
1.1 General description
The BGU7063 is a fully integrated analog-controlled variable gain amplifier module. Its
low noise and high linearity performance makes it ideal for sensitive receivers in cellular
base station applications. The BGU7063 is operating in the 1920 MHz to 1980 MHz
frequency range and has a gain control range of 35 dB. At maximum gain the noise figure
is 0.9 dB. The gain is analog-controlled having maximum gain at 0 V and minimum gain at
3.3 V. The LNA can be bypassed extending the dynamic range. The BGU7063 is
internally matched to 50 ohm, meaning no external matching is required, enabling ease of
use. It is housed in a 16 pins 8 mm 8 mm 1.3 mm leadless HLQFN16R package
SOT1301.
1.2 Features and benefits
Input and output internally matched to 50
Low noise figure of 0.9 dB
High input IP3 of 0.9 dBm
High Pi(1dB) of 12.5 dBm
Bypass mode of LNA giving high dynamic gain range
Gain control range of 0 dB to 35 dB
Single 5 V supply
Single analog gain control of 0 V to 3.3 V
Unconditionally stable up to 12.75 GHz
Moisture sensitivity level 3
ESD protection at all pins
1.3 Applications
Cellular base stations, remote radio heads
3G, LTE infrastructure
Low noise applications with variable gain and high linearity requirements
Active antenna
NXP Semiconductors
BGU7063
Analog controlled high linearity low noise variable gain amplifier
1.4 Quick reference data
Table 1. Quick reference data
VCC1 = 5 V; VCC2 = 5 V; f = 1950 MHz; Tamb = 25 C; input and output 50 ; unless otherwise specified.
Symbol Parameter
Conditions
Min Typ Max Unit
ICC(tot) total supply current
high gain mode
[1] 200 230 265 mA
low gain mode
[2] 165 190 215 mA
NF noise figure
Vctrl(Gp) = 0 V (maximum power gain)
[1] - 0.9 -
dB
Gp = 35 dB
[1] - 1.05 1.2 dB
IP3I input third-order intercept point
Gp = 35 dB; 2-tone; tone-spacing = 1.0 MHz [1] 0 0.9 - dBm
Pi(1dB) input power at 1 dB gain compression Gp = 35 dB
[1] 14 12.5 - dBm
[1] high gain mode: GS1 = LOW; GS2 = HIGH (see Table 9)
[2] low gain mode: GS1 = HIGH; GS2 = LOW (see Table 9)
2. Pinning information
2.1 Pinning
WHUPLQDO
LQGH[ DUHD
5)B,1
*1'
*6
QF
5)B287
*1'
QF
9FWUO*S
Fig 1. Pin configuration
7UDQVSDUHQW WRS YLHZ
DDD
2.2 Pin description
Table 2.
Symbol
RF_IN
GND
GS1
n.c.
Pin description
Pin
1
2, 11, 13, 16
3
4, 5, 7, 10
Description
RF input
ground
gain switch control 1
not connected, internally open
BGU7063
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 7 December 2012
© NXP B.V. 2012. All rights reserved.
2 of 16
|